Hunter Douglas Douette PowerView Installation Operation Care Download Page 27 | Manualshive

Page: 27 / 44

background image

INSTALLATION

25

■

■

Plug the long end of the cable into the
socket on the second battery wand.

■

■

Place the battery wand into the front
channel of the headrail.

If Your Order Came with One Battery Wand Only...

■

■

Plug the single power cable from the motor into the socket on the battery wand.

■

■

Place the battery wand into the front channel of the headrail. The front lip on the channel
holds the wand in position.

Second Battery Wand

«
...
25
26
27
28
29
...
»

Summary of Contents for Douette PowerView













































Reviews:

No comments

Related manuals for Douette PowerView

Brand: TDC Pages: 4

Brand: E-Z UP Pages: 2

Brand: Umbrosa Pages: 23

Brand: DHP Pages: 25

Brand: HULALA HOME Pages: 5

Brand: RiverRidge Pages: 20

Brand: Tresanti Pages: 12

Brand: Camaflexi Pages: 13

Brand: DIVERSIFIED WOODCRAFTS Pages: 6

VALENCIA 378416

Brand: Next Pages: 12

Portland Headboard

Brand: Atlantic Furniture Pages: 3

Paris Storage 424586

Brand: Next Pages: 11

MS55-018-039-23

Brand: Mainstays Pages: 12

FARMHOUSE WOOD DINING WITH PICNIC BENCHES...

Brand: HAMPTON BAY Pages: 18

OPTION TIROIR 190 400

Brand: Gami Pages: 3

Brand: Quoizel Pages: 2

Bayswater Tallboy 5 Drawer MKII White 24192439

Brand: Freedom Pages: 3

CALLA SCH-175008

Brand: GABBY Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands