Hunter Douglas Douette PowerView Installation Operation Care Download Page 12 | Manualshive

Page: 12 / 44

background image

INSTALLATION – INSIDE MOUNT

10

■

■

Attach the installation brackets using the screws provided.

IMPORTANT:

Be sure the front edges of the installation brackets are level and aligned to

each other. Use shims if necessary to level the brackets.

Mount the Headrail

■

■

Mount the headrail into the installation brackets. Do not remove any components from the
headrail. Both end plates should remain attached to the ends of the headrail.

■

➤

Place the front groove on the headrail onto the front lip of the installation bracket.

■

➤

Position the end of the headrail opposite the fabric stack flush against the jamb. This
leaves a gap on the stationary rail side. The stationary rail fills this gap when anchored.

■

➤

Rotate the rear of the headrail up and push back until the headrail snaps in place.

Gap

Left Stack Shown

Flush

Place Groove onto

Front of Bracket

Snap in

Place

«
...
10
11
12
13
14
...
»

Summary of Contents for Douette PowerView













































Reviews:

No comments

Related manuals for Douette PowerView

Brand: Gami Pages: 5

Brand: Habitat Pages: 10

Brand: Vanico Maronyx Pages: 16

Brand: Safavieh Pages: 2

Brand: Safavieh Pages: 4

Brand: Galipette Pages: 12

HAMPTON SOFA SET CORNER

Brand: Emmezeta Pages: 10

Brand: World Market Pages: 4

Sierra 2-Leg Desk SEHX30-48 Series

Brand: Workrite Ergonomics Pages: 9

Kid's Chair PKFFKCDKCHGY

Brand: P'kolino Pages: 22

KAZACHOK 198971

Brand: MAISONS DU MONDE Pages: 15

Brand: Lightolier Pages: 2

Oklahoma SL-SHSTOR-2

Brand: rst brands Pages: 21

Brand: LDI Spaces Pages: 3

Brand: Whalen Pages: 27

Brand: Tennsco Pages: 2

McKenzie 2168AUF

Brand: Whittier Wood Furniture Pages: 8

Brand: Happy Babies Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands