Hunter Douglas Douette PowerView Installation Operation Care Download Page 13 | Manualshive

Page: 13 / 44

background image

INSTALLATION

11

Install the Fabric Stack

NOTE:

The installation procedures that follow are the same for inside and outside mounts,

except where indicated.

Prepare the Fabric Stack

■

■

Insert the stationary rail bracket into the vertical rail on the side where the fabric stacks.

■

➤

The bracket fits into the grooves on the rear of the vertical rail.

■

➤

Insert the bracket until it is seated and the bracket catch snaps into the hole on the back
of the rail. Check that the bracket catch is fully engaged.

Bracket Catch

Seated Bracket

«
...
11
12
13
14
15
...
»

Summary of Contents for Douette PowerView













































Reviews:

No comments

Related manuals for Douette PowerView

Brand: J.Burrows Pages: 3

Brand: J.Burrows Pages: 2

Brand: ofichairs Pages: 3

Brand: J.Burrows Pages: 4

DONCASTER JBDONHBMBK

Brand: J.Burrows Pages: 10

Brand: J.Burrows Pages: 9

Brand: J.A.Y. Furniture Pages: 8

Brand: nardi Pages: 3

Brand: Narbutas Pages: 3

Brand: Rauch Pages: 7

Brand: OfficeSource Pages: 4

Brand: Urban Barn Pages: 2

Brand: NEXERa Pages: 16

Clive Metal Futon 758/7502

Brand: Argos Pages: 7

Brand: Furniture of America Pages: 7

Casper Office Chair

Brand: fantastic furniture Pages: 7

M22105HD 2722241

Brand: Backyard Creations Pages: 2

Brand: Unfinished Furniture of Wilmington Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands