Hunter Douglas Douette PowerView Installation Operation Care Download Page 15 | Manualshive

Page: 15 / 44

background image

INSTALLATION

13

■

■

Review the diagram below to familiarize yourself with where the fabric carrier wheels fit
inside the headrail. Note that the headrail is notched to allow insertion of the wheels.

■

➤

Above the notch is a foam block to keep the wheels in place during installation.
Compress the foam to install the fabric carrier wheels.

■

■

Insert the fabric carrier wheels into the headrail through the notch on the stationary rail
side, compressing the foam block. (Unwrap a small amount of cord from the orange cord
organizer if you need more slack.)

■

➤

The wheels with clear stems fit into the rear channel and the wheels with black stems
into the front channel.

NOTE:

The fabric carrier wheels only fit into the rail the correct way; it is not possible to

install them into the wrong channel.

IMPORTANT:

Do not attach the stationary rail bracket until after inserting all fabric carriers.

Black = Front

Clear = Rear

Foam Block

Above Notch

Clear Stem

Fabric Carriers

Black Stem

Fabric Carriers

FRONT

«
...
13
14
15
16
17
...
»

Summary of Contents for Douette PowerView













































Reviews:

No comments

Related manuals for Douette PowerView

Brand: OFM Pages: 2

Brand: Walter Knoll Pages: 26

Brand: Salamander Pages: 3

Brand: IBM Pages: 4

Brand: Palram Pages: 100

Brand: WATSON Pages: 4

Findley & Myers CBD36

Brand: CABINETS TO GO Pages: 4

Brand: Restol Pages: 9

Brand: Riotoro Pages: 31

Brand: Naturel Pages: 43

Brand: ICON Pages: 20

Hayato HYTV711L

Brand: Forte Pages: 22

Portofino Prestige OP-PEST2218A-PORVI

Brand: rst brands Pages: 15

Brand: Work Smart Pages: 2

Bibliotheque Broc Edition 131331

Brand: atmosphera Pages: 2

Brand: De La Espada Pages: 7

Brand: Safco Pages: 3

Brand: Instant Desks Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands