Hunter Douglas Douette PowerView Installation Operation Care Download Page 16 | Manualshive

Page: 16 / 44

background image

INSTALLATION

14

■

■

Install the stationary rail bracket.

■

➤

Hook the stational rail bracket to the headrail as illustrated below.

■

➤

After hooking it to the headrail, you may allow the stationary rail to hang freely.

■

■

Position the stationary rail bracket.

■

➤

To move the stationary rail bracket, pull the bottom of the rail into the room slightly
before sliding the bracket.

■

➤

Outside Mount:

Move the stationary rail bracket so that the stationary rail is aligned

with the end of the white gearbox.

■

➤

Inside Mount:

Move the stationary rail bracket so that the stationary rail is flush against

the jamb.

Stationary

Rail

Stationary

Rail Bracket

Align

Outside Mount

Inside Mount

Flush

Against

Jamb

«
...
14
15
16
17
18
...
»

Summary of Contents for Douette PowerView













































Reviews:

No comments

Related manuals for Douette PowerView

Brand: Jason.L Pages: 20

Brand: realspace Pages: 81

Brand: Lane Pages: 4

Brand: Germania Pages: 8

Brand: Lorell Pages: 3

Brand: t.akustik Pages: 3

Brand: Rauch Pages: 12

Madison Chaise JC022

Brand: Ballard Designs Pages: 5

Artemis Gaming Desk

Brand: Zenox Pages: 2

ACADIA BAR HEIGHT SWIVEL CHAIR

Brand: E.C. Woods Pages: 7

Brand: gbo Pages: 32

Brand: HABYS Pages: 20

Brand: J&K Pages: 7

Brand: Heart of House Pages: 7

Brand: Sable Pages: 24

Habitat 939/7673

Brand: Argos Pages: 7

Floating Shelf AMFS01

Brand: Amada Homefurnishing Pages: 8

Brand: BestMatic Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands