Huawei NetCol8000-A013 User Manual Download Page 87

Page: 87 / 181

Maintenance Item

Expected Result

Troubleshooting

Check that the electrical components

and control components of the

outdoor unit are free of dust.

Check that the surfaces of the

control board are not aged.

Replace the abnormal board.

Check that the electric heater

contactor works properly.

Replace the electric heating

contactor if it is faulty.

Cable

Check that no cable is aged.

Replace aged cables.

Outdoor unit

Check that the outdoor unit is

secured to the floor.

Tighten the screws that secure the

rack to the floor.

5.2 Troubleshooting

CA UTION

Do not maintain or replace outdoor units during thunderstorms. Otherwise, your

personal safety will be in danger.

NO TICE

● You are not advised to maintain or replace outdoor units in rainy days. If

unavoidable, take protective measures to prevent water from entering the

outdoor unit.

● When opening the electric control box cover, clear water from the cover.
● Certain circuits in the smart cooling product have lethal voltages. Only

professional technicians are allowed to perform maintenance.

● Exercise caution during troubleshooting with power on.
● If jumpers are used for troubleshooting, always remove them after

troubleshooting. Connected jumpers may affect control functions and damage

equipment.

Table 5-4 Troubleshooting

Cate

gory

Sympto

Possible Cause

Measure

Indo

unit

The

indoor

unit fails

to start.

The indoor fan is damaged. Replace the indoor fan.

The drive board of the

indoor fan is damaged.

Replace the drive board of the indoor fan.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

5 System Operation and Maintenance

Issue 02 (2020-11-09)

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands