Huawei NetCol8000-A013 User Manual Download Page 156

Page: 156 / 181

Figure 6-69 Version upgrade

Step 6 Press the

, and

keys to upgrade the programs of the controller,

indoor unit, and outdoor unit.
●

Controller upgrade:
–

If there are multiple controller program versions in the USB flash drive,

**Prepare Reset Controller** is displayed, the controller is reset, and the

upgrade progress bar is displayed after you press the

key. After the

upgrade is complete, the program is upgraded to the latest version.

–

If there is no controller upgrade program in the USB flash drive or the

upgrade program is consistent with the current program version, **No

Need Upgrade** is displayed.

–

If no USB flash drive is inserted, **U Disk No Detect** is displayed 15

seconds after you press the

key.

●

Indoor unit upgrade:
–

If the indoor unit upgrade program exists in the USB flash drive, the

system starts upgrading the indoor unit program and the upgrade

progress bar is displayed. After the upgrade is complete, **Upgrade

Done** is displayed.

–

If the indoor unit upgrade program in the USB flash drive is consistent

with the running program version of the indoor unit, **No Need

Upgrade** is displayed.

–

If no USB flash drive is inserted, **U Disk No Detect** is displayed 15

seconds after you press the

key.

●

Outdoor unit upgrade:
–

If the outdoor unit upgrade program exists in the USB flash drive, the

system starts upgrading the outdoor unit program and the upgrade

progress bar is displayed. After the upgrade is complete, **Upgrade

Done** is displayed.

–

If the outdoor unit upgrade program in the USB flash drive is consistent

with the running program version of the outdoor unit, **No Need

Upgrade** is displayed.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

6 FAQ

Issue 02 (2020-11-09)

149

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands