Huawei NetCol8000-A013 User Manual Download Page 49

Page: 49 / 181

Figure 3-18 Securing an indoor unit

----End

3.8 Securing an Outdoor Unit

Prerequisites

●

The M10 expansion bolts used for securing an outdoor unit have been

prepared.

●

The concrete groundwork is prepared.

Context

NO TICE

● Move the outdoor unit close to the installation position before unpacking. You

are recommended to stand the outdoor unit during transportation. If tilt is not

avoidable, the tilt degree cannot exceed 15°.

● Do not hold the fan guard on the shell. Otherwise, it will be deformed.
● Do not touch the blades using hand or any other object.
● After installing the outdoor unit, remove the protective cardboard of condenser

fin.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

3 Installation Guide

Issue 02 (2020-11-09)

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands