Huawei NetCol8000-A013 User Manual Download Page 137

Page: 137 / 181

●

If the password is incorrect, the message "Wrong Password. Enter Again" is

displayed.

Figure 6-19 Incorrect password

●

If the password is correct, the user menu screen is displayed.

Figure 6-20 Correct password

Step 5 On the user menu screen, move the cursor to User Setting by pressing the

key. Then press the

key to access the user setting submenu screen.

Step 6 Set parameters for the user setting submenu by pressing the

, and

keys.

Figure 6-21 User settings

----End

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

6 FAQ

Issue 02 (2020-11-09)

130

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands