Huawei NetCol8000-A013 User Manual Download Page 94

Page: 94 / 181

Alarm

Alarm Name

System

Action

Possible Causes

Solution

205

Comp HP Switch

Alarm

The

compressor

shuts down.

1. The condenser fins

are dirty or blocked.

2. The outdoor fan or

its drive is faulty.

3. The cables to the

high pressure switch

are loose or

damaged.

4. The high pressure

switch is faulty.

5. The refrigerant is

overfilled.

6. The outdoor unit is

not properly

installed.

1. Clean the condenser

fins.

2. Maintain or replace

the outdoor fan

drive or outdoor

fan.

3. Check the cable

connections to the

high pressure

switch.

4. Maintain or replace

the high pressure

switch.

5. Decrease certain

amount of

refrigerant.

6. Reinstall the

outdoor unit.

206

Comp HP Switch

Lock Alarm

The

compressor

shuts down.

(The alarm

needs to be

manually

cleared.)

The Comp HP Switch

Alarm is triggered

multiple times within a

specified period of

time.

Refer to the solution to

the Comp HP Switch

Alarm.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

5 System Operation and Maintenance

Issue 02 (2020-11-09)

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands