Huawei NetCol8000-A013 User Manual Download Page 71

Page: 71 / 181

Figure 4-2 Display panel starting

NO TICE

The crankcase heating belt of the compressor starts working after the equipment

is energized. Ensure that the crankcase heating belt has been preheated for more

than 12 hours before starting the compressor. Otherwise, the compressor will be

damaged. Huawei will not be liable for any consequences.

Step 3 After the startup screen ends, the screen for the initial startup password is

automatically displayed.

Figure 4-3 Initial startup screen

Step 4 Obtain the 8-digit startup password for this model through the Service Expert app

based on the model barcode and verification code.
1. Open the Service Expert app.
2. Tap StartUp on the home screen of the app.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

4 Power-On Commissioning

Issue 02 (2020-11-09)

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands