Huawei NetCol8000-A013 User Manual Download Page 56

Page: 56 / 181

3.10.2 Connecting the Condensate Drainpipe

Context

The smart cooling product condensate drainpipe inside the cabinet can be routed

from the bottom or side. Determine the pipe routing mode based on site

conditions.

Procedure

Step 1 Install the rigid pipe conversion adapter to the drainpipe connector.
Step 2 Route the external drainpipe into the cabinet through the side plate or bottom

plate. Connect the external drainpipe to the rigid pipe conversion adapter.

Figure 3-27 Bottom pipe routing

Figure 3-28 Side pipe routing

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

3 Installation Guide

Issue 02 (2020-11-09)

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands