Huawei NetCol8000-A013 User Manual Download Page 74

Page: 74 / 181

No.

Icon

Name

Description

Dehumidifi

cation

status

If the equipment enters the dehumidification

mode, 100% is displayed. If the equipment exits

from the dehumidification mode, 0% is displayed.

Lock icon

If the password has not been entered or an

incorrect password has been entered, this icon

exists. After the correct password is entered (the

setting or maintenance menu is displayed), this

icon disappears. If no operations have been

performed during the LCD backlight time

(default: 30 seconds), the main menu screen is

displayed, the display panel is locked again, and

the lock icon appears again. To access the setting

or maintenance menu, you need to re-enter the

correct password.

Monitoring

icon

If the unit is in monitoring mode, this icon exists.

Otherwise, this icon does not exist.

Teamwork

icon

If the unit is in teamwork mode, this icon exists.

Otherwise, this icon does not exist.

Alarm icon If the unit has raised an alarm, this icon blinks.

Otherwise, this icon does not exist.

----End

4.3 Setting Temperature and Humidity Values

Procedure

Step 1 Tap

, and choose Setting > User Menu by pressing the

key to

access the screen for entering the password for the user menu.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

4 Power-On Commissioning

Issue 02 (2020-11-09)

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands