Huawei NetCol8000-A013 User Manual Download Page 109

Page: 109 / 181

Alarm

Alarm Name

System

Action

Possible Causes

Solution

724

Condensation

Temp sensor fault

1. The temperature

sensor cable is not

properly connected.

2. The temperature

sensor is faulty.

1. Check the cable

connection to the

temperature sensor.

2. Maintain or replace

the temperature

sensor.

801

Return Air High

Temp Alarm

1. The heat load is

high, or the cooling

capacity is

insufficient.

2. The return air

temperature is high

shortly after the

unit is started.

3. The ambient

temperature

exceeds the upper

threshold.

4. The return air high

temperature alarm

threshold is

inappropriate for

the working

conditions.

5. The temperature

displayed by the

temperature sensor

is different from the

actual temperature.

1. Add smart cooling

products.

2. Check whether

other causes exist if

the alarm is not

cleared in a long

time after startup.

3. Check the ambient

temperature.

4. Adjust the return air

high temperature

alarm threshold.

5. Calibrate or replace

the temperature

sensor.

802

Return Air Low

Temp Alarm

1. The heat load is low

or the cooling

capacity is too high.

2. The ambient

temperature is too

low.

3. The return air low

temperature alarm

threshold is

inappropriate for

the working

conditions.

4. The temperature

displayed by the

temperature sensor

is different from the

actual temperature.

1. Reduce the number

of smart cooling

products.

2. Check the ambient

temperature.

3. Adjust the return air

low temperature

alarm threshold.

4. Calibrate or replace

the temperature

sensor.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

5 System Operation and Maintenance

Issue 02 (2020-11-09)

102

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands