Huawei NetCol8000-A013 User Manual Download Page 28

Page: 28 / 181

2.4 Operating Environment Specifications

Environmental Specifications

Table 2-3 Environmental specifications

Item

Specifications

Indoor unit

operating

temperature

18–32°C, temperature adjustment precision: ±1°C

Indoor unit

operating

humidity

20%–80% RH, humidity adjustment precision: ±5% RH

Storage

temperature

● –40°C to +70°C (indoor unit)
● –40°C to +70°C (outdoor unit without refrigerant)
● –40°C to +45°C (outdoor unit with refrigerant)

Storage

humidity

5%–95% RH (non-condensing)

Outdoor unit

operating

temperature

–20°C to +45°C

Altitude

0–4000 m, When the altitude exceeds 1000 m, the power

should be derated.

Installation Requirements

Table 2-4 Installation requirements

Item

Specifications

Equipm

ent

room

door

Width ≥ 1.2 m; height ≥ 2.3 m

Floor

Bearing capacity ≥ 350 kg/m

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

2 Product Description

Issue 02 (2020-11-09)

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands