HP 6125XLG Command Reference Manual Download Page 152 | Manualshive

Page: 152 / 466

background image

141

Field Description

Restart t3

T3 timer, in seconds.

SA Bit

Whether SA is supported:

•

Supported.

•

Not supported.

Total number of interfaces

Total number of IS-IS interfaces.

Number of waiting LSPs

Number of LSPs not obtained by the GR Restarter from
GR Helpers during LSDB synchronization.

display isis interface

Use

display isis interface

to display IS-IS interface information.

Syntax

display isis interface

[ [

interface-type interface-number

] [

verbose

] |

statistics

] [

process-id

]

Views

Any view

Predefined user roles

network-admin
network-operator

Parameters

interface-type interface-number

: Displays statistics of a specified IS-IS interface.

verbose

: Displays detailed information about an interface. If this keyword is not specified, this command

displays brief information about an interface.

statistics

: Displays IS-IS interface statistics.

process-id

: Displays IS-IS interface information for an IS-IS process specified by its ID in the range of 1 to

65535.

Usage guidelines

If no interface is specified, the command displays information about all interfaces.
If no IS-IS process is specified, the command displays all interface information for all processes.

Examples

# Display brief IS-IS interface information.

<Sysname> display isis interface

Interface information for IS-IS(1)

----------------------------------

Interface: Vlan-interface12

Id IPv4.State IPv6.State MTU Type DIS

001 Up Down 547 L1/L2 Yes/No

# Display detailed IS-IS interface information.

«
...
150
151
152
153
154
...
»

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6125XLG

Elinx EIRP305-T

Brand: B&B Electronics Pages: 19

Brand: Eaton Pages: 10

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

5big - Network NAS Server

Brand: LaCie Pages: 9

Brand: LaCie Pages: 14

12big Rack Fibre 8

Brand: LaCie Pages: 9

Brand: Salusfin Pages: 6

Brand: E-TOP Pages: 76

Brand: process-informatik Pages: 8

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brand: Abocom Pages: 1

Brand: Watchguard Pages: 40

Brand: APARIAN Pages: 2

Brand: Tbus Pages: 25

Brand: Faderfox Pages: 10

Brand: Kanguru Pages: 13

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands