HP 6125XLG Command Reference Manual Download Page 317

Page: 317 / 466

306

Default

Route reflection between clients is enabled.

Views

BGP IPv4 unicast instance view, BGP-VPN IPv4 unicast instance view, BGP IPv6 unicast instance view

Predefined user roles

network-admin

Usage guidelines

When a route reflector is configured, and the clients of a route reflector are fully meshed, route reflection

is unnecessary because it consumes more bandwidth resources. You can use the

undo reflect

between-clients

command to disable route reflection instead of modifying network configuration or

changing network topology.
After route reflection is disabled between clients, routes can still be reflected between a client and a

non-client.

Examples

# In BGP IPv4 unicast instance view, disable route reflection between clients.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv4-family unicast

[Sysname-bgp-ipv4] undo reflect between-clients

# In BGP-VPN IPv4 unicast instance view, disable route reflection between clients.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ip vpn-instance vpn1

[Sysname-bgp-vpn1] ipv4-family unicast

[Sysname-bgp-ipv4-vpn1] undo reflect between-clients

# In BGP IPv6 unicast instance view, disable route reflection between clients.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family unicast

[Sysname-bgp-ipv6] undo reflect between-clients

Related commands

•

peer reflect-client

•

reflector cluster-id

Use

reflector cluster-id

to configure the cluster ID for a route reflector.

Use

undo reflector cluster-id

to restore the default.

Syntax

reflector cluster-id

{

cluster-id

ip-address

}

undo reflector cluster-id

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Search results

Summary of Contents for 6125XLG

Reviews:

Related manuals for 6125XLG

Brands by name

Popular brands

HP 6125XLG, Command Reference Manual

Search results

Summary of Contents for 6125XLG

Reviews:

Related manuals for 6125XLG

Brands by name

Popular brands