manualshive.com logo in svg

HP 6125XLG, Command Reference Manual

The HP 6125XLG Configuration Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidance on setting up and configuring your HP 6125XLG product. Enhance your product experience by downloading the manual from manualshive.com for free.

Share
Download
background image

 

396 

Usage guidelines 

If no level is specified, this command displays both Level-1 and Level-2 route information. 

Examples 

# Display IPv6 IS-IS route information. 

<Sysname> display isis route ipv6 

 

                         Route information for IS-IS(1) 

                         ------------------------------ 

 

                         Level-1 IPv6 Forwarding Table 

                         ----------------------------- 

 

 Destination: 2001:1::                                PrefixLen: 64 

 Flag       : R/L/-                                   Cost     : 20 

 Next Hop   : FE80::200:5EFF:FE64:8905                Interface: Vlan1 

 

 Destination: 2001:2::                                PrefixLen: 64 

 Flag       : D/L/-                                   Cost     : 10 

 Next Hop   : Direct                                  Interface: Vlan1 

 

       Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set 

 

                         Level-2 IPv6 Forwarding Table 

                         ----------------------------- 

 

 Destination: 2001:1::                                PrefixLen: 64 

 Flag       : -/-/-                                   Cost     : 20 

 

 

 Destination: 2001:2::                                PrefixLen: 64 

 Flag       : D/L/-                                   Cost     : 10 

 Next Hop   : Direct                                  Interface: Vlan1 

 

       Flags: D-Direct, R-Added to Rib, L-Advertised in LSPs, U-Up/Down Bit Set 

Table 92

 

Command output 

Field Description 

Destination 

IPv6 destination prefix.

 

PrefixLen 

Length of the prefix.

 

Flag/Flags 

Route flag: 

•

 

D

—This is a direct route. 

•

 

R

—The route has been added into the routing table.  

•

 

L

—The route has been advertised in an LSP.  

•

 

U

—Route leaking flag, indicating that the Level-1 route is from Level-2. 

U

 means the 

route will not be returned to Level-2. 

 

Cost Route 

cost.

 

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6125XLG

4RF Aprisa LTE Quick Start Manual preview
Aprisa LTE
Brand: 4RF Pages: 7
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Brand: Idis Pages: 86
Paradyne Hotwire 6301 Installation Instructions Manual preview
Hotwire 6301
Brand: Paradyne Pages: 20
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Brand: Paradyne Pages: 2
?omtime CT-Router LAN User Manual preview
CT-Router LAN
Brand: ?omtime Pages: 62
AT&T Nighthawk M6 Pro Let'S Get Started preview
Nighthawk M6 Pro
Brand: AT&T Pages: 2
Paradyne Comsphere 3510 User Manual preview
Comsphere 3510
Brand: Paradyne Pages: 85
National Instruments SCXI-1120 User Manual preview
SCXI-1120
Brand: National Instruments Pages: 130
ICP DAS USA ZT-2024 Quick Start Manual preview
ZT-2024
Brand: ICP DAS USA Pages: 8
Kaptia Klever Getting Started preview
Klever
Brand: Kaptia Pages: 14
Aaeon FWS-7150 Manual preview
FWS-7150
Brand: Aaeon Pages: 57
Juniper NSM4000 Hardware Manual preview
NSM4000
Brand: Juniper Pages: 196
Buffalo LinkStation 500 User Manual preview
LinkStation 500
Brand: Buffalo Pages: 139
KYLAND Technology KIEN3016A Hardware Installation Manual preview
KIEN3016A
Brand: KYLAND Technology Pages: 19
Alcatel-Lucent 7705 SAR-A Installation Manual preview
7705 SAR-A
Brand: Alcatel-Lucent Pages: 154
ZyXEL Communications NBG6616 Quick Start Manual preview
NBG6616
Brand: ZyXEL Communications Pages: 4
Radio Shack TRS-80 PTC-64 Operation Manual preview
TRS-80 PTC-64
Brand: Radio Shack Pages: 40
QCT QuantaGrid D51PH-1ULH Service Manual preview
QuantaGrid D51PH-1ULH
Brand: QCT Pages: 167

Brands by name

Popular brands

Load more brands