manualshive.com logo in svg

HP 6125XLG, Command Reference Manual

The HP 6125XLG Configuration Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidance on setting up and configuring your HP 6125XLG product. Enhance your product experience by downloading the manual from manualshive.com for free.

Share
Download
background image

 

148 

 System Id: 5555.1111.1111 

 Interface: Vlan-interface12           Circuit Id: 7777.8888.1111.01 

 State: Up     HoldTime:  28s       Type: L2(L1L2)     PRI: 64 

# Display detailed IS-IS neighbor information. 

<Sysname> display isis peer verbose 

 

                          Peer information for ISIS(1) 

                          ---------------------------- 

 

 System Id: 5555.1111.1111 

 Interface: Vlan-interface12           Circuit Id: 7777.8888.1111.01 

 State: Up     HoldTime:  27s       Type: L1(L1L2)     PRI: 64 

 Area Address(es): 18 

 Peer IP Address(es):8.8.8.5 

 Uptime: 00:03:17 

 Adj Protocol:  IPv4 

 

 System Id: 5555.1111.1111 

 Interface: Vlan-interface12           Circuit Id: 7777.8888.1111.01 

 State: Up     HoldTime:  26s       Type: L2(L1L2)     PRI: 64 

 Area Address(es): 18 

 Peer IP Address(es):8.8.8.5 

 Uptime: 00:03:17 

 Adj Protocol:  IPv4 

Table 38

 

Command output 

Field Description 

System Id 

System ID of the neighbor. 

Interface 

Interface connecting to the neighbor.

 

Circuit Id 

Circuit ID. 

State Circuit 

state.

 

HoldTime 

Within the holdtime, if no hellos are received from the neighbor, the neighbor 
is considered down. If a hello is received, the holdtime is reset to the initial 

value.

 

Type 

Circuit type: 

•

 

L1

—The circuit type is Level-1 and the neighbor is a Level-1 router. 

•

 

L2

—The circuit type is Level-2 and the neighbor is a Level-2 router. 

•

 

L1(L1L2)

—The circuit type is Level-1 and the neighbor is a Level-1-2 router. 

•

 

L2(L1L2)

—The circuit type is Level-2 and the neighbor is a Level-1-2 router.

 

PRI 

DIS priority of the neighbor.

 

Area Address(es) 

Area address of the neighbor. 

 

Peer IP Address(es) 

IP address of the neighbor.

 

Uptime 

Time elapsed since the neighbor relationship was formed.

 

Adj Protocol 

Adjacency protocol.

 

 

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6125XLG

iDirect Evolution X3 Installation And Safety Manual preview
Evolution X3
Brand: iDirect Pages: 60
WAGO 852-1417 Operating And Assembly Instructions preview
852-1417
Brand: WAGO Pages: 2
TP-Link TD-8817 Specifications preview
TD-8817
Brand: TP-Link Pages: 3
Davey RainBank mkII Installation Instructions Manual preview
RainBank mkII
Brand: Davey Pages: 18
Far Tools MR 40PB Original Manual Translation preview
MR 40PB
Brand: Far Tools Pages: 24
Ubiquiti AmpliFi AFi-G Quick Start Manual preview
AmpliFi AFi-G
Brand: Ubiquiti Pages: 20
AMG Systems AMG9240-C User Manual preview
AMG9240-C
Brand: AMG Systems Pages: 2
Buffalo LS520D Series Quick Setup Manual preview
LS520D Series
Brand: Buffalo Pages: 2
BEC 7404 Series User Manual preview
7404 Series
Brand: BEC Pages: 159
Perle IOLAN MDC User Manual preview
IOLAN MDC
Brand: Perle Pages: 491
Juniper MX480 Hardware Manual preview
MX480
Brand: Juniper Pages: 420
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Brand: LevelOne Pages: 3
Planet WNAP-7335 Quick Installation Manual preview
WNAP-7335
Brand: Planet Pages: 2
Quatech Device Server User Manual preview
Device Server
Brand: Quatech Pages: 98
TRENDnet TEW-823DRU Quick Installation Manual preview
TEW-823DRU
Brand: TRENDnet Pages: 10
Asante IntraSwitch 5324MT Quick Installation Manual preview
IntraSwitch 5324MT
Brand: Asante Pages: 2
Baileigh 1019072 Operator'S Manual preview
1019072
Brand: Baileigh Pages: 20
Moxa Technologies PowerTrans PT-7728 Hardware Installation Manual preview
PowerTrans PT-7728
Brand: Moxa Technologies Pages: 8

Brands by name

Popular brands

Load more brands