HP 6125XLG Command Reference Manual Download Page 13

Page: 13 / 466

Table 1

Command output

Field Description

Destinations

Number of destination addresses.

Routes

Number of routes.

Destination/Mask

Destination address/mask length.

Proto

Protocol that installed the route.

Pre

Preference of the route.

Cost

Cost of the route.

NextHop

Next hop address of the route.

Interface

Output interface for packets to be forwarded along the route.

Summary Count

Number of routes.

# Display detailed information about all routes in the routing table.

<Sysname> display ip routing-table verbose

Destinations : 13 Routes : 13

Destination: 0.0.0.0/32

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 08h34m37s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NBRID: 0x10000000 LastAs: 0

AttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1000c OrigNextHop: 127.0.0.1

Label: NULL RealNextHop: 127.0.0.1

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: InLoopBack0

BkTunnel ID: Invalid BkInterface: N/A

Destination: 1.1.1.0/24

Protocol: Static Process ID: 0

SubProtID: 0x0 Age: 04h20m37s

Cost: 0 Preference: 60

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NBRID: 0x10000003 LastAs: 0

AttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 192.168.47.4

Label: NULL RealNextHop: 192.168.47.4

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: Vlan-interface21

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Search results

Summary of Contents for 6125XLG

Reviews:

Related manuals for 6125XLG

Brands by name

Popular brands

HP 6125XLG, Command Reference Manual

Search results

Summary of Contents for 6125XLG

Reviews:

Related manuals for 6125XLG

Brands by name

Popular brands