HP 6125XLG Command Reference Manual Download Page 428

Page: 428 / 466

417

Use

undo apply comm-list

to restore the default.

Syntax

apply comm-list

{

comm-list-number

comm-list-name

}

delete

undo apply comm-list

Default

No COMMUNITY attributes are deleted from BGP routes.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

comm-list-number

: Specifies a basic community list by its number in the range of 1 to 99 or an advanced

community list by its number in the range of 100 to 199.

comm-list-name

: Specifies a community list by its name, a case-sensitive string of 1 to 63 characters that

cannot comprise only numbers.

Examples

# Configure node 10 in

permit

mode for routing policy

policy1

to remove the COMMUNITY attributes

specified in community list 1 from BGP routes.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] apply comm-list 1 delete

Related commands

ip community-list

apply community

Use

apply community

to set a specified COMMUNITY attribute for BGP routes.

Use

undo apply community

to remove the configuration.

Syntax

apply community

{

none

additive

| {

community-number

&<1-32> |

aa:nn

&<1-32>

internet

no-advertise

no-export | no-export-subconfed

}

[

additive

] }

undo apply community

[

none

additive

| {

community-number

&<1-32> |

aa:nn

&<1-32>

internet |

no-advertise

no-export

no-export-subconfed

} * [

additive

] ]

Default

No COMMUNITY attribute is set for BGP routes.

Views

Routing policy node view

Predefined user roles

network-admin

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Search results

Summary of Contents for 6125XLG

Reviews:

Related manuals for 6125XLG

Brands by name

Popular brands

HP 6125XLG, Command Reference Manual

Search results

Summary of Contents for 6125XLG

Reviews:

Related manuals for 6125XLG

Brands by name

Popular brands