HP 6125XLG Command Reference Manual Download Page 430

Page: 430 / 466

419

Parameters

: Increases a cost value.

: Decreases a cost value.

value

: Specifies a cost in the range of 0 to 4294967295.

Examples

# Configure node 10 in

permit

mode for routing policy

policy1

to set a cost of 120 for OSPF external

routes.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match route-type external-type1or2

[Sysname-route-policy-policy1-10] apply cost 120

apply cost-type

Use

apply cost-type

to set a cost type for routing information.

Use

undo apply cost-type

to restore the default.

Syntax

apply cost-type

{

external

internal

type-1

type

}

undo

apply cost-type

Default

No cost type is set for routing information.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

external

: Sets the cost type to IS-IS external route.

internal

: Sets the cost type to IS-IS internal route, or sets the MED value for a matching BGP route to the

IGP metric of the route's next hop.

type-1

: Sets the cost type to OSPF Type-1 external route.

type-2

: Sets the cost type to OSPF Type-2 external route.

Usage guidelines

Used for IS-IS, the

apply cost-type internal

command sets the cost type for a matching IS-IS route to IS-IS

internal route.
Used for BGP, the

apply cost-type internal

command sets the MED for a matching BGP route learned

from an IBGP peer to the IGP metric of the route's next hop before BGP advertises the route to an EBGP

peer.

Examples

# Configure node 10 in

permit

mode for routing policy

policy1

to set the cost type for routes that have a

tag of 8 to IS-IS internal route.

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Search results

Summary of Contents for 6125XLG

Reviews:

Related manuals for 6125XLG

Brands by name

Popular brands

HP 6125XLG, Command Reference Manual

Search results

Summary of Contents for 6125XLG

Reviews:

Related manuals for 6125XLG

Brands by name

Popular brands