manualshive.com logo in svg

HP 6125XLG, Command Reference Manual

The HP 6125XLG Configuration Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidance on setting up and configuring your HP 6125XLG product. Enhance your product experience by downloading the manual from manualshive.com for free.

Share
Download
background image

 

39 

protocol

: Filters redistributed routes redistributed from the specified routing protocol, which can be 

bgp

, 

direct

, 

isis

, 

ospf

, 

rip

, and 

static

. 

process-id

: Specifies the process ID of the specified routing protocol, in the range of 1 to 65535. Specify 

a process ID when the routing protocol is 

rip

, 

ospf

, or 

isis

. If no process ID is specified, the default 

process ID is 1. 

interface-type interface-number

: Specifies an interface by its type and number. 

Usage guidelines 

If a protocol is specified, RIP filters only redistributed routes redistributed from the specified routing 

protocol. Otherwise, RIP filters all redistributed routes. 
If an interface is specified, RIP filters only routes advertised by the specified interface. Otherwise, RIP 

filters routes advertised by all RIP interfaces. 
To reference an advanced ACL (with a number from 3000 to 3999) in the command, configure the ACL 

using one of the following methods: 

•

 

To deny/permit a route with the specified destination, use the 

rule

 [ 

rule-id

 ] { 

deny

 | 

permit

 }

 ip 

source

 

sour-addr sour-wildcard

 command.  

•

 

To deny/permit a route with the specified destination and mask, use the 

rule

 [ 

rule-id

 ] { 

deny

 | 

permit

 } 

ip source

 

sour-addr sour-wildcard

 

destination

 

dest-addr dest-wildcard

 command.  

The 

source

 keyword specifies the destination address of a route and the 

destination

 keyword specifies the 

subnet mask of the route. The specified subnet mask must be contiguous. Otherwise, the mask 

configuration does not take effect. 

Examples 

# Use ACL 2000 to filter redistributed routes. 

<Sysname> system-view 

[Sysname] acl number 2000 

[Sysname-acl-basic-2000] rule deny source 192.168.10.0 0.0.0.255 

[Sysname-acl-basic-2000] quit 

[Sysname] rip 1 

[Sysname-rip-1] filter-policy 2000 export 

# Use IP prefix list 

abc

 to filter redistributed routes. 

<Sysname> system-view 

[Sysname] ip prefix-list abc index 10 permit 11.0.0.0 8 

[Sysname] rip 1 

[Sysname-rip-1] filter-policy prefix-list abc export 

# Configure ACL 3000 to permit only route 113.0.0.0/16 to pass. Use ACL 3000 to filter redistributed 
routes. 

<Sysname> system-view 

[Sysname] acl number 3000 

[Sysname-acl-adv-3000] rule 10 permit ip source 113.0.0.0 0 destination 255.255.0.0 0 

[Sysname-acl-adv-3000] rule 100 deny ip 

[Sysname-acl-adv-3000] quit 

[Sysname] rip 1 

[Sysname-rip 1] filter-policy 3000 export 

Related commands 

•

 

acl

 (

ACL and QoS Command Reference

) 

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6125XLG

D-Link Air DCS-1000W Setting-Up Manual preview
Air DCS-1000W
Brand: D-Link Pages: 13
Cabletron Systems MMAC-5FNB Overview And Setup Manual preview
MMAC-5FNB
Brand: Cabletron Systems Pages: 21
Lanpro LP-N24 Installation Instructions preview
LP-N24
Brand: Lanpro Pages: 5
Moxa Technologies ICS-G7748A Series Quick Installation Manual preview
ICS-G7748A Series
Brand: Moxa Technologies Pages: 10
Mastervolt MasterBus Tanklevel Interface User And Installation Manual preview
MasterBus Tanklevel Interface
Brand: Mastervolt Pages: 8
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Brand: LGC wireless Pages: 154
Moxa Technologies TAP-125 Series User Manual preview
TAP-125 Series
Brand: Moxa Technologies Pages: 51
Talent LT804-A Quick Installation Manual preview
LT804-A
Brand: Talent Pages: 18
Hawking H-CF30W Quick Installation Manual preview
H-CF30W
Brand: Hawking Pages: 21
ORiNG TGXPS-1080-M12-MV Series Quick Installation Manual preview
TGXPS-1080-M12-MV Series
Brand: ORiNG Pages: 2
Jensen of Scandinavia Air:Link 29150 Installation Manual preview
Air:Link 29150
Brand: Jensen of Scandinavia Pages: 2
Devolo dLAN 200 AVsmart+ Technical Data preview
dLAN 200 AVsmart+
Brand: Devolo Pages: 2
Camozzi UVIX Use And Maintenance Manual preview
UVIX
Brand: Camozzi Pages: 22
Gbord EN-203 User Manual preview
EN-203
Brand: Gbord Pages: 11
Generic IP ROUTER User Manual preview
IP ROUTER
Brand: Generic Pages: 51
Cambium Networks PTP 850E User Manual preview
PTP 850E
Brand: Cambium Networks Pages: 560
Cabletron Systems CSMIM-T1 Installation Manual preview
CSMIM-T1
Brand: Cabletron Systems Pages: 198
Zte ZXHN H368C User Manual preview
ZXHN H368C
Brand: Zte Pages: 25

Brands by name

Popular brands

Load more brands