manualshive.com logo in svg

HP 6125XLG, Command Reference Manual

The HP 6125XLG Configuration Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidance on setting up and configuring your HP 6125XLG product. Enhance your product experience by downloading the manual from manualshive.com for free.

Share
Download
background image

 

113 

[Sysname-ospf-1] area 0 

[Sysname-ospf-1-area-0.0.0.0] network 192.168.0.0 0.0.255.255 

[Sysname] interface vlan-interface 11 

[Sysname-Vlan-interface11] ospf bfd enable 

ospf cost 

Use 

ospf cost

 to set an OSPF cost for an interface. 

Use 

undo ospf cost

 to restore the default. 

Syntax 

ospf cost 

value

 

undo ospf cost 

Default 

An interface computes its OSPF cost according to the interface bandwidth.  

Views 

Interface view 

Predefined user roles 

network-admin 

Parameters 

value

: Specifies an OSPF cost in the range of 0 to 65535 for a loopback interface and in the range of 

1 to 65535 for other interfaces. 

Usage guidelines 

The default OSPF cost is 100 Mbps/Interface bandwidth (Mbps): 

•

 

When the cost the interface computes is greater than 65535, the default OSPF cost is 65535. 

•

 

When the cost the interface computes is less than 1, the default OSPF cost is 1. 

The 

ospf cost

 command sets an OSPF cost for an interface. If you do not use this command, the interface 

automatically computes its OSPF cost.  

Examples 

# Set the OSPF cost on VLAN-interface 10 to 65. 

<Sysname> system-view 

[Sysname] interface vlan-interface 10 

[Sysname-Vlan-interface10] ospf cost 65 

ospf dr-priority 

Use 

ospf dr-priority

 to set the router priority for DR/BDR election on an interface.  

Use 

undo ospf dr-priority

 to restore the default value. 

Syntax 

ospf dr-priority

 priority

 

undo ospf dr-priority 

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6125XLG

OCCITALINA OXTOPUS EIA-709 User Manual preview
OXTOPUS EIA-709
Brand: OCCITALINA Pages: 54
Garderos R-7700 Series Operating Manual preview
R-7700 Series
Brand: Garderos Pages: 23
APARIAN DH485 Quick Start Manuals preview
DH485
Brand: APARIAN Pages: 2
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
TP-Link ER8411 Installation Manual preview
ER8411
Brand: TP-Link Pages: 2
Abocom PLS342 Specification Sheet preview
PLS342
Brand: Abocom Pages: 2
E-LINX EIR410-2SFP-T User Manual preview
EIR410-2SFP-T
Brand: E-LINX Pages: 24
Z-Wave RAZBERRY 7 PRO Quick Start Manual preview
RAZBERRY 7 PRO
Brand: Z-Wave Pages: 6
H3C SecPath F1070 Manual preview
SecPath F1070
Brand: H3C Pages: 68
Transition Networks N-FXE-xxx-01 User Manual preview
N-FXE-xxx-01
Brand: Transition Networks Pages: 5
One Identity Safeguard for Privileged Sessions 3000 Installation Manual preview
Safeguard for Privileged Sessions 3000
Brand: One Identity Pages: 37
Hama 53178 Instruction Manual preview
53178
Brand: Hama Pages: 45
netsys NH-310S User Manual preview
NH-310S
Brand: netsys Pages: 38
Juniper PTX10002-60C Quick Start Manual preview
PTX10002-60C
Brand: Juniper Pages: 9
Dahua Technology NVR52A16-16P-4KS2 Quick Start Manual preview
NVR52A16-16P-4KS2
Brand: Dahua Technology Pages: 13
Ericsson Baseband 6648 Manual preview
Baseband 6648
Brand: Ericsson Pages: 16
King Pigeon N80 User Manual preview
N80
Brand: King Pigeon Pages: 8
Westermo Viper 408 Manual preview
Viper 408
Brand: Westermo Pages: 22

Brands by name

Popular brands

Load more brands