manualshive.com logo in svg

HP 6125XLG, Command Reference Manual

The HP 6125XLG Configuration Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidance on setting up and configuring your HP 6125XLG product. Enhance your product experience by downloading the manual from manualshive.com for free.

Share
Download
background image

 

14 

      Label: NULL           RealNextHop: :: 

    BkLabel: NULL             BkNextHop: N/A 

  Tunnel ID: Invalid          Interface: NULL0 

BkTunnel ID: Invalid        BkInterface: N/A 

 

Destination: FF00::/8 

   Protocol: Direct          Process ID: 0 

  SubProtID: 0x0                    Age: 00h53m50s 

       Cost: 0               Preference: 0 

        Tag: 0                    State: Active NoAdv 

  OrigTblID: 0x0                OrigVrf: default-vrf 

    TableID: 0xa                 OrigAs: 0 

      NBRID: 0x20000001          LastAs: 0 

     AttrID: 0xffffffff        Neighbor: :: 

      Flags: 0x10014        OrigNextHop: :: 

      Label: NULL           RealNextHop: :: 

    BkLabel: NULL             BkNextHop: N/A 

  Tunnel ID: Invalid          Interface: NULL0 

BkTunnel ID: Invalid        BkInterface: N/A 

Table 5

 

Command output 

Field Description 

Destination 

IPv6 address and prefix of the destination network or host. 

Protocol 

Protocol that installed the route. 

SubProtID 

ID of the subprotocol for routing. 

Age 

Time for which the route has been in the routing table. 

Cost 

Cost of the route. 

Preference 

Preference of the route. 

Tag 

Tag of the route. 

State 

Route status: 

•

 

Active

—Active unicast route. 

•

 

Adv

—Route that can be advertised. 

•

 

Inactive

—Inactive route. 

•

 

NoAdv

—Route that the router must not advertise. 

•

 

Vrrp

—Routes generated by VRRP. 

•

 

Nat

—Routes generated by NAT. 

•

 

TunE

—Tunnel. 

OrigTblID 

Original routing table ID. 

OrigVrf 

Original VPN that the route belongs to. 

TableID 

ID of the routing table. 

OrigAs 

Original AS number. 

NBRID 

Neighbor ID of the route. 

LastAs 

Last AS number. 

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6125XLG

Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
N-Tron 702-W User Manual & Installation Manual preview
702-W
Brand: N-Tron Pages: 62
National Instruments NI 9265 Operating Instructions Manual preview
NI 9265
Brand: National Instruments Pages: 26
National Instruments NI 9203 User Manual And Specifications preview
NI 9203
Brand: National Instruments Pages: 85
National Instruments Module SCXI-1503 User Manual preview
Module SCXI-1503
Brand: National Instruments Pages: 79
Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Brand: Paradyne Pages: 2
Paradyne Hotwire 6381 Installation Instructions Manual preview
Hotwire 6381
Brand: Paradyne Pages: 20
Paradyne Hotwire 6381 Upgrade Instructions preview
Hotwire 6381
Brand: Paradyne Pages: 2
Zhone Hotwire 6381 Quick Installation Instructions preview
Hotwire 6381
Brand: Zhone Pages: 2
Paradyne COMSPHERE 6800 Series Multiplexer Management And Configuration Manual preview
COMSPHERE 6800 Series
Brand: Paradyne Pages: 155
Paradyne COMSPHERE 6800 Series Communications Products Support Configuration Manual preview
COMSPHERE 6800 Series
Brand: Paradyne Pages: 44
NETGEAR AC1450 Installation Manual preview
AC1450
Brand: NETGEAR Pages: 14
Lancom GS-2310P Instruction Manual preview
GS-2310P
Brand: Lancom Pages: 25
AOpen 4-Port 10/100Mbps Ethernet Broadband Router User Manual preview
4-Port 10/100Mbps Ethernet Broadband Router
Brand: AOpen Pages: 41
ZyXEL Communications Dimension ES-3124 User Manual preview
Dimension ES-3124
Brand: ZyXEL Communications Pages: 228
Moxa Technologies PT-7710 Series Hardware Installation Manual preview
PT-7710 Series
Brand: Moxa Technologies Pages: 2
Global Sun GL-241101 User Manual preview
GL-241101
Brand: Global Sun Pages: 39
ZyXEL Communications P-335U Specifications preview
P-335U
Brand: ZyXEL Communications Pages: 2

Brands by name

Popular brands

Load more brands