HP 6125XLG Command Reference Manual Download Page 24

Page: 24 / 466

Destination: FF00::/8 Protocol : Direct

NextHop : :: Preference: 0

Interface : NULL0 Cost : 0

Table 4

Command output

Field Description

Destinations

Number of destination addresses.

Routes

Number of routes.

Destination

IPv6 address and prefix of the destination network or host.

NextHop

Next hop address of the route.

Preference

Preference of the route.

Interface

Output interface for packets to be forwarded along the route.

Protocol

Protocol that installed the route.

Cost

Cost of the route.

Summary Count

Number of routes.

# Display detailed information about all routes in the routing table.

<Sysname> display ipv6 routing-table verbose

Destinations : 3 Routes : 3

Destination: ::1/128

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 00h53m50s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NBRID: 0x20000000 LastAs: 0

AttrID: 0xffffffff Neighbor: ::

Flags: 0x10004 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: InLoopBack0

BkTunnel ID: Invalid BkInterface: N/A

Destination: FE80::/10

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 00h53m50s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NBRID: 0x20000002 LastAs: 0

AttrID: 0xffffffff Neighbor: ::

Flags: 0x10084 OrigNextHop: ::

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Search results

Summary of Contents for 6125XLG

Reviews:

Related manuals for 6125XLG

Brands by name

Popular brands

HP 6125XLG, Command Reference Manual

Search results

Summary of Contents for 6125XLG

Reviews:

Related manuals for 6125XLG

Brands by name

Popular brands