manualshive.com logo in svg

HP 6125XLG, Command Reference Manual

The HP 6125XLG Configuration Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidance on setting up and configuring your HP 6125XLG product. Enhance your product experience by downloading the manual from manualshive.com for free.

Share
Download
background image

 

174 

Default 

The priority of Level-1 and Level-2 is 64. 

Views 

Interface view 

Predefined user roles 

network-admin 

Parameters 

value

: Specifies a DIS priority in the range of 0 to 127.  

level-1

: Applies the DIS priority to Level-1.  

level-2

: Applies the DIS priority to Level-2.  

Usage guidelines 

If neither 

level-1

 nor 

level-2

 is specified, the DIS priority applies to both Level-1 and Level-2.  

On an IS-IS broadcast network, a router must be elected as the DIS at each routing level. Specify a DIS 

priority at a level for an interface. The greater the interface’s priority is, the more likelihood it becomes 

the DIS. If multiple routers in the broadcast network have the same highest DIS priority, the router with the 
highest Subnetwork Point of Attachment (SNPA) address (SNPA addresses are MAC addresses on a 

broadcast network) becomes the DIS. 
IS-IS has no backup DIS. The router with a priority of 0 can also participate in DIS election.  

Examples 

# Configure the Level-2 DIS priority as 127 for VLAN-interface 10.  

<Sysname> system-view 

[Sysname] interface vlan-interface 10 

[Sysname-Vlan-interface10] isis dis-priority 127 level-2 

isis enable 

Use 

isis enable

 to enable an IS-IS process on an interface.  

Use 

undo isis enable

 to disable IS-IS. 

Syntax 

isis enable

 [ 

process-id

 ] 

undo

 

isis enable

 

Default 

No IS-IS process is enabled on an interface. 

Views 

Interface view 

Predefined user roles 

network-admin 

Parameters 

process-id

: Specifies an IS-IS process by its ID in the range of 1 to 65535. The default is 1.  

Summary of Contents for 6125XLG



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6125XLG

Sangamo CHOICE PR1 User Instructions preview
CHOICE PR1
Brand: Sangamo Pages: 2
peplink balance ONE Manual preview
balance ONE
Brand: peplink Pages: 2
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Brand: Ubiquiti Pages: 13
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Brand: GarrettCom Pages: 10
Patton electronics ipRocketLink 3086FR Quick Start Manual preview
ipRocketLink 3086FR
Brand: Patton electronics Pages: 12
Thecus N2520 series User Manual preview
N2520 series
Brand: Thecus Pages: 130
Genexis FiberTwist XGS2410 Installation Manual preview
FiberTwist XGS2410
Brand: Genexis Pages: 7
Carrier 40VMW005 Installation And Maintenance Instructions Manual preview
40VMW005
Brand: Carrier Pages: 18
Qvis 72-8P Series User Manual preview
72-8P Series
Brand: Qvis Pages: 233
TRENDnet TDM-C400 User Manual preview
TDM-C400
Brand: TRENDnet Pages: 205
H3C WT2024-U-PWR Compliance And Safety Manual preview
WT2024-U-PWR
Brand: H3C Pages: 51
NETGEAR DG834GUV5 User Manual preview
DG834GUV5
Brand: NETGEAR Pages: 120
SMC Networks EZ Switch SMC-1026DT V.2 User Manual preview
EZ Switch SMC-1026DT V.2
Brand: SMC Networks Pages: 27
Dahua Technology VDA-NVR2108W4KS2 User Manual preview
VDA-NVR2108W4KS2
Brand: Dahua Technology Pages: 363
Orcomm DILX-GW Operation Manual preview
DILX-GW
Brand: Orcomm Pages: 10
EtherWAN EX17016 Installation Manual preview
EX17016
Brand: EtherWAN Pages: 2
Billion BiPAC 7404VGO Specifications preview
BiPAC 7404VGO
Brand: Billion Pages: 2
Riverbed SteelCentral AppResponse 2170 Installation Manual preview
SteelCentral AppResponse 2170
Brand: Riverbed Pages: 166

Brands by name

Popular brands

Load more brands