Honda Automobiles 2009 Accord Owner'S Manual Download Page 26 | Manualshive

Page: 26 / 412

background image

CONTINUED

During a frontal crash, your seat belt
restrains your lower body and torso,
and the front airbag helps protect
your head and chest.

Although both airbags normally
inflate within a split second of each
other, it is possible for only one
airbag to deploy.

This can happen if the severity of a
collision is at the margin, or
threshold, that determines whether
or not the airbags will deploy. In
such cases, the seat belt will provide
sufficient protection, and the
supplemental protection offered by
the airbag would be minimal.

Only the driver’s airbag can deploy if
there is no passenger in the front
seat, or if the advanced airbag
system has turned the passenger’s
airbag off (see page

).

If you ever have a moderate to
severe frontal collision, sensors will
detect the vehicle’s rapid
deceleration.

If the rate of deceleration is high
enough, the control unit will instantly
inflate the driver’s and front
passenger’s airbags, at the time and
with the force needed.

An indicator on the instrument
panel that alerts you that the
passenger’s side airbag has been
turned off (see page

).

An indicator on the dashboard that
alerts you that the passenger’s
front airbag has been turned off
(see page

).

Emergency backup power in case
your vehicle’s electrical system is
disconnected in a crash.

29

30

26

Additional Information About Your Airbags

How Your Front Airbags Work

Dr
iv

er
and

P

asseng

er
Saf

e

ty

23

０８／０６／１１１８：２４：５０３１ＴＥ０６１０００２８

2009 Accord Coupe

«
...
24
25
26
27
28
...
»

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Accord

Brand: Federal Signal Corporation Pages: 13

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: Spiral Audio Pages: 2

Brand: Xhorse Pages: 48

Brand: Oldsmobile Pages: 354

Brand: KEKO Pages: 13

Stealth 4191F Series

Brand: Road Armor Pages: 5

Brand: Acura Pages: 6

Brand: Lantronix Pages: 51

Brand: Reliant Pages: 206

Brand: Scion Pages: 24

Brand: Blue Ox Pages: 8

Brand: MSD Ignition Pages: 4

Brand: XLifter Pages: 24

HomeLink 2882082

Brand: Polaris Pages: 8

Mazda BT50 RW-50/15

Brand: Polaris Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands