Honda Automobiles 2009 Accord Owner'S Manual Download Page 257

Page: 257 / 412

Wait a few minutes after turning the
engine off before you check the oil.

Insert the dipstick all the way back
into its hole.

Remove the dipstick again, and
check the level. It should be
between the upper and lower
marks.

Remove the dipstick (orange
handle/loop).

Wipe off the dipstick with a clean
cloth or paper towel.

If it is near or below the lower mark,
see

on page

306

Oil Check

Adding Engine Oil

Service Station Procedures

254

UPPER MARK

LOWER MARK

2.4

engine models

V6 models

2.4

engine models

DIPSTICK
(orange handle)

DIPSTICK (orange loop)

０８／０６／１１１９：０２：５７３１ＴＥ０６１００２５９

2009 Accord Coupe

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Search results

Summary of Contents for 2009 Accord

Reviews:

Related manuals for 2009 Accord

Brands by name

Popular brands

Honda Automobiles 2009 Accord, Owner'S Manual

Search results

Summary of Contents for 2009 Accord

Reviews:

Related manuals for 2009 Accord

Brands by name

Popular brands