Honda Automobiles 2009 Accord Owner'S Manual Download Page 286 | Manualshive

Page: 286 / 412

background image

Driving with varying tire or wheel
sizes may cause the VSA to
malfunction. When replacing tires,
make sure they are of the same size
and type as your original tires (see
page

).

VSA is turned on every time you
start the engine, even if you turned it
off the last time you drove the
vehicle.

If you install winter tires, make sure
they are the same size as those that
were originally supplied with your
vehicle. Exercise the same caution
during winter driving as you would if
your vehicle was not equipped with
VSA.

In certain unusual conditions when
your vehicle gets stuck in shallow
mud or fresh snow, it may be easier
to free it with the VSA temporarily
switched off. When the VSA system
is off, the traction control system is
also off. You should only attempt to
free your vehicle with the VSA off if
you are not able to free it when the
VSA is on.

Immediately after freeing your
vehicle, be sure to switch the VSA on
again. We do not recommend driving
your vehicle with the VSA and
traction control systems switched off.

This switch is under the driver’s side
vent. To turn the VSA system on and
off, press and hold it until you hear a
beep.

When VSA is off, the VSA activation
indicator comes on as a reminder.
Press and hold the switch again. It
turns the system back on.

341

VSA and Tire Sizes

VSA Of f Switch

Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System

D

riv

ing

283

VSA OFF SWITCH

０８／０６／１１１９：０７：３８３１ＴＥ０６１００２８８

2009 Accord Coupe

«
...
284
285
286
287
288
...
»

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Accord

Brand: Triumph Pages: 86

V2 SUPERCHARGER

Brand: Tesla Pages: 9

Brand: Carax Pages: 2

Brand: iArmor Pages: 4

Brand: Mazda Pages: 122

Easy Air Auto Screen

Brand: Wagan Pages: 8

Brand: ROLEC Pages: 2

Brand: Mercedes-Benz Pages: 24

Brand: Macally Pages: 10

ASENTO EV-EXP18R

Brand: ADAPT SOLUTIONS Pages: 25

Brand: Blue Bird Pages: 111

Brand: Chevrolet Pages: 406

IONIQ HYBRID 2019

Brand: Hyundai Pages: 16

Brand: Yakima Pages: 14

Brand: Pacbrake Pages: 2

Brand: Kuda Pages: 2

Brand: Kia Pages: 38

Brand: Lenoxx Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands