Honda Automobiles 2009 Accord Owner'S Manual Download Page 313 | Manualshive

Page: 313 / 412

background image

−

−

Always use Honda Long-life Anti-
freeze/Coolant Type 2. This coolant
is pre-mixed with 50 percent
antifreeze and 50 percent distilled
water. Never add straight antifreeze
or plain water.

If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system for leaks.

If Honda antifreeze/coolant is not
available, you may use another
major-brand non-silicate coolant as a
temporary replacement. Make sure it
is a high-quality coolant
recommended for aluminum engines.
Continued use of any non-Honda
coolant can result in corrosion,
causing the cooling system to
malfunction or fail. Have the cooling
system flushed and refilled with
Honda antifreeze/coolant as soon as
possible.

2.4

engine models only

Adding Engine Coolant

Engine Coolant

310

RESERVE TANK

RESERVE TANK

V6 models

2.4

engine models

If you regularly drive your vehicle
under severe conditions in very low
temperature (under

31°F,

35°C), a

higher concentration of coolant should
be used. Consult your Honda dealer
f or more inf ormation of the proper
coolant.

０８／０６／１１１９：１１：５６３１ＴＥ０６１００３１５

2009 Accord Coupe

«
...
311
312
313
314
315
...
»

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Accord

Brand: Kargo Master Pages: 5

Brand: Kargo Master Pages: 6

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

21 COVERT Series

Brand: Code 3 Pages: 16

Brand: Baja Designs Pages: 5

Dunlop L.D02.C.M

Brand: Sumitomo Pages: 22

Brand: Arrista Pages: 2

Brand: CSL Pages: 8

Brand: Kuda Pages: 3

Brand: Prorack Pages: 17

Brand: WALMEC Pages: 6

Brand: FORM FIT Pages: 11

Brand: Chevrolet Pages: 416

Brand: Toyota Pages: 5

DVD Travel Automotive

Brand: Hama Pages: 2

Brand: Hama Pages: 2

Brand: Hama Pages: 36

Brand: Haltech Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands