Honda Automobiles 2009 Accord Owner'S Manual Download Page 272 | Manualshive

Page: 272 / 412

background image

Apply the parking brake.

In cold weather, turn off all
electrical accessories to reduce
the drain on the battery.

Press the clutch pedal down all the
way. The START (III) position
does not function unless the clutch
pedal is pressed.

Make sure the shift lever is in
Park. Press on the brake pedal.

If the engine does not start within
15 seconds, or starts but stalls
right away, repeat step 4 with the
accelerator pedal pressed halfway
down. If the engine starts, release
pressure on the accelerator pedal
so the engine does not race.

If the engine fails to start, press
the accelerator pedal all the way
down, and hold it there while
starting to clear flooding. If the
engine still does not start, return
to step 5.

Without touching the accelerator
pedal, turn the ignition key to the
START (III) position. Do not hold
the key in the START (III)
position for more than 15 seconds
at a time. If the engine does not
start right away, pause for at least
10 seconds before trying again.

1.

2.

3.

4.

5.

6.

Manual transmission:

Automatic transmission:

Starting the Engine

D

riv

ing

269

The engine is harder to start in cold
weather. Also, the thinner air f ound at
altitudes above 8,000 f eet (2,400
meters) adds to this problem.

The immobilizer system protects your
vehicle f rom thef t. If an improperly
coded key (or other device) is used, the
engine’s f uel system is disabled. For
more inf ormation, see page

.

78

０８／０６／１１１９：０５：２９３１ＴＥ０６１００２７４

2009 Accord Coupe

«
...
270
271
272
273
274
...
»

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Accord

Brand: ZAPTEC Pages: 240

Brand: Axxess Pages: 8

inView 360 Fusion

Brand: Safe Fleet Pages: 27

ROADSIDE ASSISTANCE

Brand: Seat Pages: 44

Brand: Fiat Pages: 24

Brand: Valeo Pages: 28

Brand: FALCON RIDGE Pages: 7

Brand: Volvo Pages: 30

Brand: Toyota Pages: 636

Brand: Hyundai Pages: 19

HU-4421-XL-SDK01

Brand: FALCON RIDGE Pages: 5

Brand: Oldsmobile Pages: 354

Brand: Saab Pages: 15

Brand: Alphasonik Pages: 8

LED Dominator TAM83S2

Brand: Whelen Engineering Company Pages: 2

Brand: Billien Pages: 2

Brand: Lexus Pages: 28

Brand: Magneti Marelli Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands