Honda Automobiles 2009 Accord Owner'S Manual Download Page 312 | Manualshive

Page: 312 / 412

background image

Install a new oil filter according to
the instructions that come with it.

Refill the engine with the recom-
mended oil.

Engine oil change capacity
(including filter):

Replace the engine oil fill cap.
Start the engine. The oil pressure
indicator should go out within 5
seconds. If it does not, turn off the
engine, and check your work.

Let the engine run for several
minutes, then check the drain bolt
and oil filter for leaks.

Turn off the engine, let it sit for
several minutes, then check the oil
level on the dipstick. If necessary,
add more oil.

Make sure to clean off any dirt
and dust on the connecting
surface of a new oil filter.

Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten the drain bolt to:

4.

5.

6.

7.

8.

9.

V6 models

2.4

engine models

Changing the Engine Oil and Filter

Ma

int
e

na
nce

309

OIL FILTER

OIL FILTER

2.4

engine models

V6 models

4.4 US qt (4.2 )

29 lbf·ft (39 N·m , 4.0 kgf·m)

4.5 US qt (4.3 )

Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.

０８／０６／１１１９：１１：４７３１ＴＥ０６１００３１４

2009 Accord Coupe

«
...
310
311
312
313
314
...
»

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Accord

Brand: Subaru Pages: 3

Brand: PEUGEOT Pages: 128

Brand: Schumacher Electric Pages: 87

2009 ESCALADE ESV

Brand: Cadillac Pages: 602

Brand: Thule Pages: 8

Automotive 31006

Brand: KRAFTWERK Pages: 2

2016 Sandero Stepway

Brand: Renault Pages: 183

Brand: Mercedes-Benz Pages: 368

Brand: Jeep Pages: 380

Brand: Toro Pages: 24

Brand: Cadillac Pages: 407

Dodge Challenger SRT8®Challenger SRT8 392 2012

Brand: Dodge Pages: 5

Brand: Edelbrock Pages: 2

Brand: Ford Pages: 256

Brand: r.LiNK Pages: 21

Brand: Toyota Pages: 672

Brand: Acura Pages: 19

Brand: Ford Pages: 325

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands