Honda Automobiles 2009 Accord Owner'S Manual Download Page 317 | Manualshive

Page: 317 / 412

background image

Pour the fluid slowly and carefully
so you do not spill any. Clean up
any spill immediately; it could
damage components in the engine
compartment.

Remove the dipstick and check
the fluid level. It should be
between the upper and lower
marks.

If the level is below the lower
mark, add fluid into the dipstick
hole to bring it to the level
between the upper and lower
marks.

Always use Honda Genuine
ATF-Z1 (automatic transmission
fluid).

Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.

The transmission should be drained
and refilled with new fluid according
to the maintenance minder (see page

).

If you are not sure how to add fluid,
contact your dealer.

5.

4.

6.

297

Transmission Fluid

314

V6 models

LOWER
MARK

UPPER
MARK

Use only Honda Genuine ATF-Z1
(Automatic Transmission Fluid). Do
not mix with other transmission f luids.
Using transmission f luid other than
Honda Genuine ATF-Z1 may cause
deterioration in transmission operation
and durability, and could result in
damage to the transmission.
Damage resulting f rom the use of
transmission f luid other than Honda
Genuine ATF-Z1 is not covered by the
Honda new vehicle warranty.

０８／０６／１１１９：１２：３９３１ＴＥ０６１００３１９

2009 Accord Coupe

«
...
315
316
317
318
319
...
»

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Accord

21 COVERT Series

Brand: Code 3 Pages: 16

Brand: Chevrolet Pages: 2

Brand: Whelen Engineering Company Pages: 9

PRIME DESIGN VBI-FT21B

Brand: Safe Fleet Pages: 12

Plusone Console 4521011B

Brand: Honda Pages: 4

Brand: Mercedes-Benz Pages: 39

Brand: Vauxhall Pages: 131

1506-PHX Cargo Plus

Brand: Ranger design Pages: 8

Brand: AUTOTECH Pages: 1

Brand: Lexus Pages: 34

Brand: Toyota Pages: 32

Brand: ECS Pages: 4

Brand: Whispbar Pages: 15

Brand: WABCO Pages: 34

Brand: AUTOTECH Pages: 4

Brand: Revelation Pages: 4

Brand: Or-Fab Pages: 3

Brand: Navman Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands