Honda Automobiles 2009 Accord Owner'S Manual Download Page 332

Page: 332 / 412

To change the bulb, start the
engine, turn the steering wheel all
the way to the right, then turn off
the engine.

Use a flat-tipped screwdriver to
remove the two holding clips from
the inner fender, and pull the inner
fender cover back.

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.

Push the electrical connector back
onto the bulb. Make sure it is on
all the way.

Reinstall the under cover and put
the three fasteners back in place.

Reinstall the inner fender. Make
sure it is installed under the edge
of the front bumper.

Reinstall the holding clips, and
push in its head of each clip.

Remove the electrical connector
from the bulb by pushing on the
tab and pulling the connector
down.

Remove the bulb from the fog
light assembly by turning it one-
quarter turn counterclockwise.

Turn on the fog lights to test the
new bulb.

10.

11.

Passenger’s side

Driver’s side

Lights

int
e

na
nce

329

HOLDING CLIPS

ELECTRICAL CONNECTOR

TAB

０８／０６／１１１９：１５：１９３１ＴＥ０６１００３３４

2009 Accord Coupe

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Search results

Summary of Contents for 2009 Accord

Reviews:

Related manuals for 2009 Accord

Brands by name

Popular brands

Honda Automobiles 2009 Accord, Owner'S Manual

Search results

Summary of Contents for 2009 Accord

Reviews:

Related manuals for 2009 Accord

Brands by name

Popular brands