Honda Automobiles 2009 Accord Owner'S Manual Download Page 91

Page: 91 / 412

Battery type: CR1616

Avoid dropping or throwing the
transmitter.

Protect the transmitter from
extreme temperature.

Do not immerse the transmitter in
any liquid.

If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.

To replace the battery:

Remove the screw at the base of
the transmitter with a small
Phillips-head screwdriver.

Separate the transmitter by prying
its middle seam with your
fingernail.

If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.

Be careful when removing

this screw as the head of the screw
can strip out.

Remote Transmitter

Replacing the Transmitter Battery

Remote Transmitter Care

NOTE:

SCREW

０８／０６／１１１８：３６：０３３１ＴＥ０６１０００９３

2009 Accord Coupe

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Search results

Summary of Contents for 2009 Accord

Reviews:

Related manuals for 2009 Accord

Brands by name

Popular brands

Honda Automobiles 2009 Accord, Owner'S Manual

Search results

Summary of Contents for 2009 Accord

Reviews:

Related manuals for 2009 Accord

Brands by name

Popular brands