Honda Automobiles 2009 Accord Owner'S Manual Download Page 116

Page: 116 / 412

The console compartment is
equipped with a detachable tray.

To remove this tray, slide it forward,
then pull it up.

To close, lower the armrest, and
push it down until it latches.

Open the front beverage holder by
pulling up on the lid.

Each rear side panel also has a
beverage holder.

To open the console compartment,
pull up on the lever and lift the
armrest.

Except LX and LX-S

Interior Convenience Items

Console Compartment

Inst

nt
s

Cont

113

CONSOLE COMPARTMENT

FRONT

DETACHABLE TRAY

LEVER

０８／０６／１１１８：３９：４５３１ＴＥ０６１００１１８

2009 Accord Coupe

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Search results

Summary of Contents for 2009 Accord

Reviews:

Related manuals for 2009 Accord

Brands by name

Popular brands

Honda Automobiles 2009 Accord, Owner'S Manual

Search results

Summary of Contents for 2009 Accord

Reviews:

Related manuals for 2009 Accord

Brands by name

Popular brands