Honda Automobiles 2009 Accord Owner'S Manual Download Page 321 | Manualshive

Page: 321 / 412

background image

Check the fluid level in the
reservoirs monthly. There are up to
two reservoirs, depending on the
model. They are:

Brake fluid reservoir (all models)
Clutch fluid reservoir
(manual transmission only)

Replace the brake fluid according to
the maintenance minder (see page

).

Always use Honda Heavy Duty
Brake Fluid DOT 3. If it is not
available, you should use only DOT 3
or DOT 4 fluid, from a sealed
container, as a temporary
replacement.

Using any non-Honda brake fluid can
cause corrosion and decrease the life
of the system. Have the brake
system flushed and refilled with
Honda Heavy Duty Brake Fluid
DOT 3 as soon as possible.

Brake fluid marked DOT 5 is not
compatible with your vehicle’s
braking system and can cause
extensive damage.

The fluid level should be between
the MIN and MAX marks on the side
of the reservoir. If the level is at or
below the MIN mark, your brake
system needs attention. Have the
brake system inspected for leaks or
worn brake pads.

297

Brake and Clutch Fluid

Brake Fluid

318

MAX

MIN

０８／０６／１１１９：１３：１５３１ＴＥ０６１００３２３

2009 Accord Coupe

«
...
319
320
321
322
323
...
»

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Accord

Brand: Daihatsu Pages: 1718

Retrotech RTX-68D-CHG

Brand: Dakota Digital Pages: 4

Brand: Whispbar Pages: 15

Brand: Toyota Pages: 52

Brand: Actia Pages: 102

Brand: ideus Pages: 159

Brand: Ecco Pages: 9

Sedan CIVIC 2022

Brand: Honda Pages: 701

2010 MX-5 Miata

Brand: Mazda Pages: 8

RAV-4 2015 Series

Brand: Toyota Pages: 50

Brand: Cadillac Pages: 529

Brand: Toro Pages: 16

Brand: Mercedes-Benz Pages: 10

Brand: Metra Electronics Pages: 20

3 Facelift 2006

Brand: Mazda Pages: 94

Brand: v.link Pages: 19

Brand: Ford Pages: 264

Brand: Kleinn Air Horns Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands