Honda Automobiles 2009 Accord Owner'S Manual Download Page 48 | Manualshive

Page: 48 / 412

background image

To deactivate the lockable retractor
and remove a child seat, unlatch the
buckle, unroute the seat belt, and let
the belt fully retract.

Push and pull the child seat
forward and from side-to-side to
verify that it is secure enough to
stay upright during normal driving
maneuvers. If the child seat is not
secure, unlatch the belt, allow it to
retract fully, then repeat these
steps.

After confirming that the belt is
locked, grab the shoulder part of
the belt near the buckle, and pull
up to remove any slack from the
lap part of the belt. Remember, if
the lap part of the belt is not tight,
the child seat will not be secure.

To remove slack, it may help to
put weight on the child seat, or
push on the back of the seat while
pulling up on the belt.

5.

4.

Installing a Child Seat

Dr
iv

er
and

P

asseng

er
Saf

e

ty

45

０８／０６／１１１８：２８：２５３１ＴＥ０６１０００５０

2009 Accord Coupe

«
...
46
47
48
49
50
...
»

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Accord

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

Brand: B-Speech Pages: 4

BTFREQ PRO BTFMPD3SR

Brand: Scosche Pages: 16

Brand: Mercedes-Benz Pages: 358

Brand: Beper Pages: 52

Brand: Oldsmobile Pages: 358

Brand: Edelbrock Pages: 2

Brand: Mercedes-Benz Pages: 93

Brand: Calix Pages: 4

Brand: Axxess Pages: 8

Brand: Metra Electronics Pages: 8

Brand: Edelbrock Pages: 2

Brand: Hudson Pages: 77

Brand: Guardsman Pages: 2

Brand: Goobay Pages: 2

Brand: Mazda Pages: 605

Brand: Yakima Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands