Honda Automobiles 2009 Accord Owner'S Manual Download Page 98 | Manualshive

Page: 98 / 412

background image

To get into the rear seat on the
driver’s side, open the door and pull
up on the seat-back adjustment lever.
The seat-back will tilt forward to
allow easier entry to the rear seat.

After a passenger gets into the rear
seat, push the seat-back to the
upright position and push the whole
seat backwards until it latches. Make
sure the seat is fully latched before
sitting in it.

To get into the rear seat on the
passenger’s side, push downward on
the release lever at the base of the
seat-back, or pull up on the seat-back
adjustment lever. The seat-back will
tilt forward and the entire seat will
move forward to allow easier entry to
the rear seat.

LX, LX-S and EX models

Passenger’s Side

Seats

Inst

ru

m

e

nt
s

a

nd

Cont

ro

ls

95

SEAT-BACK ADJUSTMENT LEVER

RELEASE LEVER

SEAT-BACK ADJUSTMENT LEVER

To avoid damaging the seat-back angle
adjustment motor, do not operate the
seat-back angle switch when the seat-
back is tilted f orward.

０８／０６／１１１８：３７：１１３１ＴＥ０６１００１００

2009 Accord Coupe

«
...
96
97
98
99
100
...
»

Summary of Contents for 2009 Accord





























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Accord

Brand: Alpine Pages: 69

Brand: Allen Sports Pages: 2

Brand: Mobile Create Pages: 15

Brand: Ironton Pages: 7

Brand: Chevrolet Pages: 344

Brand: Prorack Pages: 15

inView 360 Fusion

Brand: Safe Fleet Pages: 27

ROADSIDE ASSISTANCE

Brand: Seat Pages: 44

Brand: SilverLeaf Electronics Pages: 16

Brand: Yakima Pages: 15

Brand: RAM Pages: 330

Brand: AutoLoc Pages: 6

Brand: Ford Pages: 15

Brand: Honda Pages: 3

PRIME DESIGN HRR3-E-PM52

Brand: Safe Fleet Pages: 12

CHALLENGER GK-6125A 2018

Brand: Coolster Pages: 45

Brand: Magneti Marelli Pages: 9

Brand: Mazda Pages: 196

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands