manualshive.com logo in svg

Holtek HT32F54231, User Manual, Page: 414 / 576

Share
Download
Holtek HT32F54231 User Manual Download Page 414

Rev. 1.00 

414 of 576

January 28, 2022

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F54231/HT32F54241/HT32F54243/HT32F54253

19  W

atchdog T

imer (WDT)

Watchdog Timer Mode Register 0 – WDTMR0

This register specifies the Watchdog timer Counter-Reload value and reset enable control.
Offset:

0x004

Reset value: 0x0000_0FFF

31

30

29

28

27

26

25

24

Reserved

Type/Reset

23

22

21

20

19

18

17

16

Reserved

WDTEN

Type/Reset

RW 0

15

14

13

12

11

10

9

8

WDTSHLT WDTRSTEN Reserved

WDTV

Type/Reset RW 0 RW 0 RW 0

RW 1 RW 1 RW 1 RW 1

7

6

5

4

3

2

1

0

WDTV

Type/Reset RW 1 RW 1 RW 1 RW 1 RW 1 RW 1 RW 1 RW 1

Bits

Field

Descriptions

[16]

WDTEN

Watchdog Timer Running Enable

0: Watchdog Timer is disabled

1: Watchdog Timer is enabled to run

When the Watchdog Timer is disabled, the counter will be reset to its hardware 

default condition. When the WDTEN bit is set, the Watchdog Timer will be reloaded 

with the WDTV value and count down.

[15:14]

WDTSHLT

Watchdog Timer Sleep Halt

00: The Watchdog runs when the system is in the Sleep mode or Deep-Sleep1 

mode

01: The Watchdog runs when the system is in the Sleep mode and halts in 

Deep-Sleep1 mode

10 or 11: The Watchdog halts when the system is in the Sleep mode and 

Deep-Sleep1 mode

Note that the Watchdog timer always halts when the system is in the Deep-Sleep2 

mode. The Watchdog timer stops counting when the WDTSHLT field is properly 

configured in the Sleep mode or Deep-Sleep1 mode. When the Watchdog stops 

counting, the count value is retained so that it continues counting after the system 

wakes up from these three sleep modes. If a Watchdog reset occurs in the Sleep or 

Deep-Sleep1 mode, it will wake up the device. 

[13]

WDTRSTEN Watchdog Timer Reset Enable

0: A Watchdog Timer underflow or error has no effect on the system reset

1: A Watchdog Timer underflow or error triggers a Watchdog Timer system reset

[11:0]

WDTV

Watchdog Timer Counter Value

WDTV defines the value loaded into the 12-bit Watchdog down-counter.

Summary of Contents for HT32F54231

































































































































































































































































































































































































































































































































































































Reviews:

No comments