manualshive.com logo in svg

Holtek HT32F54231, User Manual, Page: 123 / 576

Share
Download
Holtek HT32F54231 User Manual Download Page 123

Rev. 1.00 

123 of 576

January 28, 2022

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F54231/HT32F54241/HT32F54243/HT32F54253

7  Reset Control Unit (RSTCU)

8  General Purpose I/O (GPIO)

8 

8 

 General Purpose I/O (GPIO)

Introduction

There are up to 40 General Purpose I/O ports, GPIO, named PA0 ~ PA15, PB0 ~ PB15 and PC0 

~ PC7 for the HT32F54231/HT32F54241 devices and up to 54 General Purpose I/O ports, GPIO, 

named PA0 ~ PA15, PB0 ~ PB15, PC0 ~ PC15 and PD0 ~ PD5 for the HT32F54243/HT32F54253 

devices to implement the logic input/output functions. Each of the GPIO ports has related control 

and configuration registers to satisfy the requirement of specific applications. The actual available 

General Purpose I/O port numbers are dependent on the device specification and package type. Refer 

to the device datasheet for detailed information.

The GPIO ports are pin-shared with other alternative functions (AFs) to obtain maximum flexibility 

on the package pins. The GPIO pins can be used as alternative functional pins by configuring the 

corresponding registers regardless of the AF input or output pins.

The external interrupts on the GPIO pins of the device have related control and configuration 

registers in the External Interrupt Control Unit (EXTI).

PxDOUTn

PxRSTn
PxSETn

PxDINn

PxINENn

PxDIRn

PxDVn

PxODn

PxPDn
PxPUn

To IOPAD PUN

To IOPAD PDN

To IOPAD DS

To IOPAD OEN

To IOPAD IEN

IEN

AFIO

OEN

AFIO

C

IOPAD

To AFIO MUX

Bus Interface

Figure 22.  GPIO Block Diagram

Summary of Contents for HT32F54231

































































































































































































































































































































































































































































































































































































Reviews:

No comments