manualshive.com logo in svg

Holtek HT32F54231, User Manual, Page: 241 / 576

Share
Download
Holtek HT32F54231 User Manual Download Page 241

Rev. 1.00 

241 of 576

January 28, 2022

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F54231/HT32F54241/HT32F54243/HT32F54253

14  General-Purpose T

imer (GPTM)

14  General-Purpose T

imer (GPTM)

Update Management

The Update event is used to update the CRR, the PSCR, the CHxACR and the CHxCCR values 

from the actual registers to the corresponding shadow registers. An update event occurs when the 

counter overflows or underflows, the software update control bit is triggered or an update event 

from the slave controller is generated.

The UEVDIS bit in the CNTCFR register can determine whether the update event occurs or 

not. When the update event occurs, the corresponding update event interrupt will be generated 

depending upon whether the update event interrupt generation function is enabled or not by 

configuring the UGDIS bit in the CNTCFR register. For more detailed description, refer to the 

UEVDIS and UGDIS bit definition in the CNTCFR register

UEVDIS

UEV (Update PSCR, CRR, 

CHxCCR, CHxACR

Shadow Registers)

Slave Restart mode  

UGDIS

Counter Overflow / Underflow

UEVDIS

UEV interrupt

UEVG

Slave Restart mode

Update Event Management

Update Event Interrupt Management

UEVG

Counter Overflow / Underflow

Figure 65.  Update Event Setting Diagram

Summary of Contents for HT32F54231

































































































































































































































































































































































































































































































































































































Reviews:

No comments