manualshive.com logo in svg

Holtek HT32F54231, User Manual, Page: 385 / 576

Share
Download
Holtek HT32F54231 User Manual Download Page 385

Rev. 1.00 

385 of 576

January 28, 2022

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F54231/HT32F54241/HT32F54243/HT32F54253

16  Single-Channel T

imer (SCTM)

16  Single-Channel T

imer (SCTM)

Channel Output Configuration Register – CHOCFR

This register specifies the channel output mode configuration.
Offset:

0x040

Reset value: 0x0000_0000

31

30

29

28

27

26

25

24

Reserved

Type/Reset

23

22

21

20

19

18

17

16

Reserved

Type/Reset

15

14

13

12

11

10

9

8

Reserved

Type/Reset

7

6

5

4

3

2

1

0

Reserved

CHPRE

Reserved

CHOM

Type/Reset

RW 0

RW 0 RW 0 RW 0

Bits

Field

Descriptions

[4]

CHPRE

Channel Capture/Compare Register (CHCCR) Preload Enable

0: CHCCR preload function is disabled

The CHCCR register can be immediately assigned a new value when the 

CHPRE bit is cleared to 0 and the updated CHCCR value is used immediately.

1: CHCCR preload function is enabled

The new CHCCR value will not be transferred to its shadow register until the 

update event occurs.

[2:0]

CHOM

Channel Output Mode Setting

These bits define the functional types of the output reference signal CHOREF.

000: No Change

001: Output 0 on compare match

010: Output 1 on compare match

011: Output toggles on compare match

100: Force inactive – CHOREF is forced to 0

101: Force active – CHOREF is forced to 1

110: PWM mode 1

- During up-counting, channel has an active level when CNTR < CHCCR or 

otherwise has an inactive level.

111: PWM mode 2

- During up-counting, channel has an inactive level when CNTR < CHCCR 

or otherwise has an active level.

Summary of Contents for HT32F54231

































































































































































































































































































































































































































































































































































































Reviews:

No comments