Hitachi SH7095 Hardware User Manual Download Page 285 | Manualshive

Page: 285 / 532

background image

274 Hitachi

•

The DMA master enable (DME) bit in the DMAOR is cleared to 0.

Clearing the DME bit in the DMAOR forcibly aborts the transfers on all channels at the end
of the current bus cycle. When the transfer is the final transfer, TE = 1 and the transfer ends.

9.4

Examples of Use

9.4.1

DMA Transfer Between On-Chip SCI and External Memory

In the following example, data received on the on-chip serial communications interface (SCI) is
transferred to external memory using DMAC channel 1. Table 9.9 shows the transfer conditions
and register settings.

Table 9.9

Register Settings for Transfers between On-Chip SCI and External Memory

Transfer Conditions

Register

Setting

Transfer source: RDR of on-chip SCI

SAR1

H'FFFFFE05

Transfer destination: external memory (word space)

DAR1

Destination address

Number of transfers: 64

TCR1

H'0040

Transfer destination address: incremented

CHCR1

H'4045

Transfer source address: fixed

Bus mode: cycle-steal

Transfer unit: byte

DEI interrupt request generated at end of transfer (DE = 1)

Channel priority: Fixed (0 > 1) (DME = 1)

DMAOR

H'0001

Transfer request source (transfer request signal): SCI (RXI)

DRCR1

H'01

Note:

Check the CPU interrupt level when interrupts are enabled in the SCI.

9.5

Notes

1.

DMA request/response selection control registers 0 and 1 (DRCR0 and DRCR1) should be
accessed in bytes. All other registers should be accessed in longword units.

2.

Before rewriting CHCR0, CHCR1, DRCR0, and DRCR1, first clear the DE bit of the
specified channel to 0 or clear the DME bit of the DMAOR to 0.

3.

When the DMAC is not operating, the NMIF bit of the DMAOR is set even when an NMI
interrupt is input.

4.

When the cache is used as the on-chip RAM, the DMAC cannot access this RAM.

5.

Set to standby mode after the DME bit of the DMAOR is set to 0.

6.

Do not access the DMAC, BSC, and UBC on-chip peripheral modules.

«
...
283
284
285
286
287
...
»

Summary of Contents for SH7095





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7095

ILDA Gem Laser projector tool

Brand: Stanwax Laser Pages: 3

Brand: Lorex Pages: 186

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

Brand: Klark Teknik Pages: 50

Brand: Grizzly Pages: 9

SmartMesh IA-510 D2511

Brand: Dust Networks Pages: 30

Brand: Uniden Pages: 5

Brand: XtendLan Pages: 52

Brand: ZALMAN Pages: 16

EK-FC750 GTX Series

Brand: ekwb Pages: 2

Brand: M-system Pages: 4

Bolide BN-NVR/NX

Brand: GSA Pages: 101

Brand: 8e6 Technologies Pages: 94

Brand: Matrix Switch Corporation Pages: 48

Brand: VIA Technologies Pages: 2

PSJ-VZ58 gen3 OEM

Brand: Grizzly Pages: 12

Brand: A4Tech Pages: 8

32R1860 - Nortel Layer 2/3 Copper GbE Switch...

Brand: IBM Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands