manualshive.com logo in svg

Hitachi SH7095, Hardware User Manual

The Hitachi SH7095 Hardware User Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device. Available for free download at manualshive.com, this manual offers detailed explanations and troubleshooting tips, ensuring a seamless user experience with the Hitachi SH7095. Get your manual now!

Share
Download
background image

114 Hitachi

3.

When set for sequential conditions (the SEQ bit of BRCR is 1) and the instruction fetch cycle
of the A channel CPU is set as a condition, set channel A for before instruction execution
(PCBA bit of BRCR is 0).

4.

When register settings are changed, the write values usually become valid after three cycles.
For on-chip memory, instruction fetches get two instructions simultaneously. If a break
condition is set on the fetch of the second of these two instructions but the contents of the
UBC registers are changed so as to alter the break condition immediately after the first of the
two instructions is fetched, a user break interrupt will still occur before the second instruction.
To ensure the timing of the change in the setting, read the register written last as a dummy.
The changed settings will be valid thereafter.

5.

When a user break interrupt is generated upon a match of the instruction fetch condition and
the conditions match again in the UBC while the exception processing service routine is
executing, the break will cause exception processing when the I3–I0 bits of the SR are set to
14 or lower. When masking addresses, when setting instruction fetch and after-execution as
break conditions, and when executing in steps, the UBC’s exception processing service
routine should not cause a match of addresses with the UBC.

6.

When the emulator is used, the UBC is used on the emulator system side to implement the
emulator's break function. This means none of the UBC functions can be used when the
emulator is being used.

6.3.8

SH7000-Series Compatibility Mode

1.

In SH7000-series compatible mode:

In SH7000-series compatible mode, functions are as follows:

•

The registers shown in the lower table in section 1.3, Register Configuration, are valid; all
others are not.

•

External bus breaks are not possible in SH7000 mode. The instruction fetch cycle occurs
prior to instruction execution. The flags are not set when break conditions match.

2.

Differences between SH7000 compatible mode and SH7095 mode:

When set for CPU instruction fetch cycle in the SH7000-series compatible mode, the break
occurs before the instruction that matches the conditions. The break conditions differ as
shown below from setting for before-execution in SH7095 mode. For data access cycles, the
address is always compared to 32 bits in the SH7000-series compatible mode, but in SH7095
mode is compared as shown in table 6.3. This produces the differences in break conditions
shown in table 6.4.

Summary of Contents for SH7095





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7095

Moxa Technologies UC-8100 Series Hardware User Manual preview
UC-8100 Series
Brand: Moxa Technologies Pages: 19
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Brand: LGC wireless Pages: 154
Matrox Millennium P650 User Manual preview
Millennium P650
Brand: Matrox Pages: 54
Accom WSD/HDe Installation Procedure preview
WSD/HDe
Brand: Accom Pages: 15
National Instruments PCI-6110E/6111E User Manual preview
PCI-6110E/6111E
Brand: National Instruments Pages: 113
Tektronix CTS 850 User Manual preview
CTS 850
Brand: Tektronix Pages: 178
IBM 8677 - BladeCenter Rack-mountable - Power Supply Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power Supply
Brand: IBM Pages: 126
NKE BOX Wi-Fi User Manual And Installation Manual preview
BOX Wi-Fi
Brand: NKE Pages: 15
LaCie FireWire 800 ExpressCard 34 Quick Install Manual preview
FireWire 800 ExpressCard 34
Brand: LaCie Pages: 24
ETAS XETK-S22.0 User Manual preview
XETK-S22.0
Brand: ETAS Pages: 84
ICS ELECTRONICS VXI-5501 Quick Start Manual preview
VXI-5501
Brand: ICS ELECTRONICS Pages: 4
Extron electronics VERSATOOLS MTP User Manual preview
VERSATOOLS MTP
Brand: Extron electronics Pages: 19
OWC ENVOY PRO MINI User Manual preview
ENVOY PRO MINI
Brand: OWC Pages: 7
TP-Link VIGI Quick Start Manual preview
VIGI
Brand: TP-Link Pages: 2
Transition Networks PCM16-FX-LC-01 User Manual preview
PCM16-FX-LC-01
Brand: Transition Networks Pages: 5
Velleman K8048 Manual preview
K8048
Brand: Velleman Pages: 14
ABB COM600 series 5.1 User Manual preview
COM600 series 5.1
Brand: ABB Pages: 42
Huawei Quidway S6500 Series Command Manual preview
Quidway S6500 Series
Brand: Huawei Pages: 845

Brands by name

Popular brands

Load more brands