manualshive.com logo in svg

Hitachi H8S/2376 F-ZTAT, Hardware Manual

The Hitachi H8S/2376 F-ZTAT is a cutting-edge microcontroller renowned for its exceptional performance and reliability. Unlock the full potential of this device by accessing the comprehensive Hardware Manual, available for free download at manualshive.com. Get detailed insights and optimize your experience with this exceptional product.

Share
Download
background image

Rev. 1.0, 09/01, page 745 of 904

4. The ADST bit is not cleared automatically, and steps [2] to [3] are repeated as long as the

ADST bit remains set to 1. When the ADST bit is cleared to 0, A/D conversion stops and the
A/D converter enters wait state.

17.4.3

Input Sampling and A/D Conversion Time

The A/D converter has a built-in sample-and-hold circuit.  The A/D converter samples the analog
input when A/D conversion start delay time (t

D

) passes after the ADST bit is set to 1, then starts

conversion.  Figure 17.2 shows the A/D conversion timing.  Table 17.3 indicates the A/D
conversion time.

As indicated in figure 17.2, the A/D conversion time (t

CONV

) includes t

D

 and the input sampling time

(t

SPL

).  The length of t

D

 varies depending on the timing of the write access to ADCSR.  The total

conversion time therefore varies within the ranges indicated in tables 17.3.

In scan mode, the values given in tables 17.3 apply to the first conversion time.  The values given
in tables 17.4 apply to the second and subsequent conversions.

(1)

(2)

t

D

t

SPL

t

CONV

ø

Address

Write signal

Input sampling
timing

ADF

Legend
(1)

: ADCSR write cycle

(2)

: ADCSR address

t

D

: A/D conversion start delay time

t

SPL

: Input sampling time

t

CONV

: A/D conversion time

Figure 17.2   A/D Conversion Timing

Table 17.3

A/D Conversion Time (Single Mode)

Summary of Contents for H8S/2376 F-ZTAT






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2376 F-ZTAT

Rabbit 2000 Designers Handbook preview
2000
Brand: Rabbit Pages: 45
Rabbit 2000 Instruction & Reference Manual preview
2000
Brand: Rabbit Pages: 174
Rabbit 2000 Getting Started preview
2000
Brand: Rabbit Pages: 43
Paradyne 3163 Quick Reference preview
3163
Brand: Paradyne Pages: 16
ICP DAS USA ZT-2510 Series Quick Start Manual preview
ZT-2510 Series
Brand: ICP DAS USA Pages: 8
Paradyne FrameSaver 9120 Installation Instruction Supplement preview
FrameSaver 9120
Brand: Paradyne Pages: 2
B&B Electronics Parallel Printer Card PIOC User Manual preview
Parallel Printer Card PIOC
Brand: B&B Electronics Pages: 16
Dolphin IBP-G4x16-2 User Manual preview
IBP-G4x16-2
Brand: Dolphin Pages: 9
Renesas H8/3864 Series User Manual preview
H8/3864 Series
Brand: Renesas Pages: 20
WABCO CAN Router Manual preview
CAN Router
Brand: WABCO Pages: 29
ICS ELECTRONICS VXI-5501 Quick Start Manual preview
VXI-5501
Brand: ICS ELECTRONICS Pages: 4
Smacq Technologies PCI-1232 User Manual preview
PCI-1232
Brand: Smacq Technologies Pages: 22
Air Live AirVideo-100 Quick Setup Manual preview
AirVideo-100
Brand: Air Live Pages: 2
ST STM32L4P5AG User Manual preview
STM32L4P5AG
Brand: ST Pages: 37
nox Hummer H-240CL Manual preview
Hummer H-240CL
Brand: nox Pages: 16
Williams Sound DW SY 1 User Manual preview
DW SY 1
Brand: Williams Sound Pages: 2
Classe Audio CT-SSP Owner'S Manual preview
CT-SSP
Brand: Classe Audio Pages: 70
Patton electronics ForeFront 2616RC Getting Started Manual preview
ForeFront 2616RC
Brand: Patton electronics Pages: 80

Brands by name

Popular brands

Load more brands