manualshive.com logo in svg

Hitachi H8S/2376 F-ZTAT, Hardware Manual

The Hitachi H8S/2376 F-ZTAT is a cutting-edge microcontroller renowned for its exceptional performance and reliability. Unlock the full potential of this device by accessing the comprehensive Hardware Manual, available for free download at manualshive.com. Get detailed insights and optimize your experience with this exceptional product.

Share
Download
background image

Rev. 1.0, 09/01, page 102 of 904

5.7

Usage Notes

5.7.1

Contention between Interrupt Generation and Disabling

When an interrupt enable bit is cleared to 0 to mask interrupts, the masking becomes effective
after execution of the instruction.

When an interrupt enable bit is cleared to 0 by an instruction such as BCLR or MOV, if an
interrupt is generated during execution of the instruction, the interrupt concerned will still be
enabled on completion of the instruction, and so interrupt exception handling for that interrupt will
be executed on completion of the instruction. However, if there is an interrupt request of higher
priority than that interrupt, interrupt exception handling will be executed for the higher-priority
interrupt, and the lower-priority interrupt will be ignored. The same also applies when an interrupt
source flag is cleared to 0. Figure 5.6 shows an example in which the TCIEV bit in the TPU’s
TIER_0 register is cleared to 0. The above contention will not occur if an enable bit or interrupt
source flag is cleared to 0 while the interrupt is masked.

Internal
address bus

Internal
write signal

φ

TCIEV

TCFV

TCIV
interrupt signal

TIER_0 write cycle by CPU

TCIV exception handling

TIER_0 address

Figure 5.6   Contention between Interrupt Generation and Disabling

Summary of Contents for H8S/2376 F-ZTAT






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2376 F-ZTAT

Eaton INDGW-X2 Manual preview
INDGW-X2
Brand: Eaton Pages: 10
T&D RTR-50 User Manual preview
RTR-50
Brand: T&D Pages: 122
SIIG NN-EC2812-S1 Quick Installation Manual preview
NN-EC2812-S1
Brand: SIIG Pages: 12
Intel SRCSASBB8I - RAID Controller Hardware User'S Manual preview
SRCSASBB8I - RAID Controller
Brand: Intel Pages: 36
Western Digital Scorpio WD2500BPVT Product Specifications preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 3
Western Digital Scorpio WD2500BPVT Product Features preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 4
Roland VP-9000 Turbostart preview
VP-9000
Brand: Roland Pages: 2
Realtek RTL8187SE User Manual preview
RTL8187SE
Brand: Realtek Pages: 30
S&T kontron COMe-cEL6 User Manual preview
kontron COMe-cEL6
Brand: S&T Pages: 99
Neo Instruments Mini Vent User Manual preview
Mini Vent
Brand: Neo Instruments Pages: 2
A4Tech RH-10 User Manual preview
RH-10
Brand: A4Tech Pages: 8
Isee IGEPv2 BOARD Hardware Reference Manual preview
IGEPv2 BOARD
Brand: Isee Pages: 68
Nortel BayStack 660 Use Manual preview
BayStack 660
Brand: Nortel Pages: 163
Baracoda Scan Dongle User Manual preview
Scan Dongle
Brand: Baracoda Pages: 16
PairGain T1L2PY0AA Manual preview
T1L2PY0AA
Brand: PairGain Pages: 80
Xtreme SNMP-1PMINI User & Installation Manual preview
SNMP-1PMINI
Brand: Xtreme Pages: 83
Vacron VDH-NK300 Hardware Manual preview
VDH-NK300
Brand: Vacron Pages: 16
DFRobot FIT0677 Assembly Manual preview
FIT0677
Brand: DFRobot Pages: 30

Brands by name

Popular brands

Load more brands