manualshive.com logo in svg

Hitachi H8S/2376 F-ZTAT, Hardware Manual

The Hitachi H8S/2376 F-ZTAT is a cutting-edge microcontroller renowned for its exceptional performance and reliability. Unlock the full potential of this device by accessing the comprehensive Hardware Manual, available for free download at manualshive.com. Get detailed insights and optimize your experience with this exceptional product.

Share
Download
background image

Rev. 1.0, 09/01, page 382 of 904

9.2.2

DTC Mode Register B (MRB)

MRB selects the DTC operating mode.

Bit

Bit Name

Initial Value

R/W

Description

7

CHNE

Undefined

−

DTC Chain Transfer Enable

When this bit is set to 1, a chain transfer will be
performed. For details, refer to 9.5.4, Chain Transfer.

In data transfer with CHNE set to 1, determination of
the end of the specified number of transfers, clearing
of the activation source flag, and clearing of DTCER
is not performed.

6

DISEL

Undefined

−

DTC Interrupt Select

When this bit is set to 1, a CPU interrupt request is
generated every time after a data transfer ends.
When this bit is set to 0, a CPU interrupt request is
generated at the time when the specified number of
data transfer ends.

5

CHNS

Undefined

−

DTC Chain Transfer Select

Specifies the chain transfer condition.

0: Chain transfer every time

1: Chain transfer only when transfer counter = 0

4
to
0

−

Undefined

−

Reserved

These bits have no effect on DTC operation, and
should always be written with 0.

9.2.3

DTC Source Address Register (SAR)

SAR is a 24-bit register that designates the source address of data to be transferred by the DTC.
For word-size transfer, specify an even source address.

9.2.4

DTC Destination Address Register (DAR)

DAR is a 24-bit register that designates the destination address of data to be transferred by the
DTC. For word-size transfer, specify an even destination address.

9.2.5

DTC Transfer Count Register A (CRA)

CRA is a 16-bit register that designates the number of times data is to be transferred by the DTC.

In normal mode, the entire CRA functions as a 16-bit transfer counter (1 to 65,536). It is
decremented by 1 every time data is transferred, and transfer ends when the count reaches H'0000.

Summary of Contents for H8S/2376 F-ZTAT






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2376 F-ZTAT

Ebyte E43-900T13S3 Manual preview
E43-900T13S3
Brand: Ebyte Pages: 8
Magma PE6R4-I Quick Installation Manual preview
PE6R4-I
Brand: Magma Pages: 2
PaloAlto Networks PA-7500 Quick Start Manual preview
PA-7500
Brand: PaloAlto Networks Pages: 3
SAF Phoenix G2 IDU Quick Start Manual preview
Phoenix G2 IDU
Brand: SAF Pages: 30
ebm-papst VBH0630CTTRS Operating Instructions Manual preview
VBH0630CTTRS
Brand: ebm-papst Pages: 16
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Brand: Enterasys Pages: 58
Sangoma A200 Analog Installation Manual preview
A200 Analog
Brand: Sangoma Pages: 6
PMD DK55110 Manual preview
DK55110
Brand: PMD Pages: 74
AXIOMTEK CEM820 Series User Manual preview
CEM820 Series
Brand: AXIOMTEK Pages: 58
Hauppauge WinTV-DVB Installation And Reference Manual preview
WinTV-DVB
Brand: Hauppauge Pages: 62
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Brand: GarrettCom Pages: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Brand: Adaptec Pages: 14
Cypress Semiconductor CY7C027AV Specification Sheet preview
CY7C027AV
Brand: Cypress Semiconductor Pages: 18
Fast FV3000-W2K Instruction Manual preview
FV3000-W2K
Brand: Fast Pages: 66
Hologic ThinPrep 3000 Operator'S Manual preview
ThinPrep 3000
Brand: Hologic Pages: 256
Mobatime DTS 4020.timebridge Mounting And Instruction Manual preview
DTS 4020.timebridge
Brand: Mobatime Pages: 94
Z3 Technology FSDI-1XA User Manual preview
FSDI-1XA
Brand: Z3 Technology Pages: 83

Brands by name

Popular brands

Load more brands