Hitachi H8S/2376 F-ZTAT Hardware Manual Download

Page: 13 / 949

Rev. 1.0, 09/01, page xiii of xliv

8.6.2

Module Stop State ................................................................................................376

8.6.3

EDREQ

Pin Falling Edge Activation...................................................................376

8.6.4

Activation Source Acceptance .............................................................................376

8.6.5

Enabling Interrupt Requests when IRF = 1 in EDMDR.......................................377

8.6.6

ETEND

Pin and CBR Refresh Cycle ...................................................................377

Section 9 Data Transfer Controller (DTC) ....................................................... 379

9.1

Features .............................................................................................................................379

9.2

Register Configuration ......................................................................................................380
9.2.1

DTC Mode Register A (MRA).............................................................................381

9.2.2

DTC Mode Register B (MRB) .............................................................................382

9.2.3

DTC Source Address Register (SAR) ..................................................................382

9.2.4

DTC Destination Address Register (DAR) ..........................................................382

9.2.5

DTC Transfer Count Register A (CRA)...............................................................382

9.2.6

DTC Transfer Count Register B (CRB) ...............................................................383

9.2.7

DTC Enable Registers A to H (DTCERA to DTCERH)......................................383

9.2.8

DTC Vector Register (DTVECR) ........................................................................383

9.3

Activation Sources ............................................................................................................384

9.4

Location of Register Information and DTC Vector Table ................................................385

9.5

Operation...........................................................................................................................388
9.5.1

Normal Mode .......................................................................................................390

9.5.2

Repeat Mode ........................................................................................................391

9.5.3

Block Transfer Mode ...........................................................................................392

9.5.4

Chain Transfer......................................................................................................393

9.5.5

Interrupts ..............................................................................................................394

9.5.6

Operation Timing .................................................................................................395

9.5.7

Number of DTC Execution States........................................................................396

9.6

Procedures for Using DTC ................................................................................................397
9.6.1

Activation by Interrupt .........................................................................................397

9.6.2

Activation by Software ........................................................................................397

9.7

Examples of Use of the DTC ............................................................................................397
9.7.1

Normal Mode .......................................................................................................397

9.7.2

Chain Transfer......................................................................................................398

9.7.3

Chain Transfer when Counter = 0 ........................................................................399

9.7.4

Software Activation .............................................................................................400

9.8

Usage Notes ......................................................................................................................401
9.8.1

Module Stop Mode Setting ..................................................................................401

9.8.2

On-Chip RAM......................................................................................................401

9.8.3

DTCE Bit Setting .................................................................................................401

9.8.4

DMAC Transfer End Interrupt .............................................................................401

9.8.5

Chain Transfer......................................................................................................401

Section 10 I/O Ports .......................................................................................... 403

Summary of Contents for H8S/2376 F-ZTAT






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for H8S/2376 F-ZTAT

Reviews:

Related manuals for H8S/2376 F-ZTAT

Brands by name

Popular brands

Hitachi H8S/2376 F-ZTAT, Hardware Manual

Search results

Summary of Contents for H8S/2376 F-ZTAT

Reviews:

Related manuals for H8S/2376 F-ZTAT

Brands by name

Popular brands